2,518 topics in this forum

1. In-House Solutions is now offering their generic controller master posts for FREE! (Yes, you heard that right!)

   By DanielGingras, April 3, 2023
   • 15 replies
   • 3.1k views
   • 
   • crazy^millman
   • April 18

2. Post Processor sharing is Prohibited on this Forum

   By ihsDavidM, June 22, 2023
   • 0 replies
   • 1.7k views
   • 
   • ihsDavidM
   • June 22, 2023

3. Looking to get a post that will use your machine to its full potential?

   By Webby, March 3, 2011
   • 0 replies
   • 23.8k views
   • 
   • Webby
   • March 3, 2011

4. Free mpmaster and mplmaster post processors.

   By Webby, March 3, 2011
   • 0 replies
   • 31.5k views
   • 
   • Webby
   • March 3, 2011

5. Haas 3x mill post not updating work offset when needed...

   By usernameinvalid, March 9
   • 4 replies
   • 297 views
   • 
   • usernameinvalid
   • 4 hours ago

6. HAAS ST20y Lathe

   By wilson424, January 24, 2018
   • 5 replies
   • 2.4k views
   • 
   • gcode
   • Yesterday at 12:36 AM

7. Plunge FeedRate

   By PcRobotic, August 16, 2019
   • 7 replies
   • 2.2k views
   • 
   • JParis
   • Tuesday at 01:14 PM

8. Integrating G234 in fanuc 5x generic post

   By ikertx0, April 7
   • 8 replies
   • 316 views
   • 
   • ikertx0
   • Monday at 03:46 PM

9. CY_Deburr_error@MPLMASTER

   By Alan Chen, April 13
   • 3 replies
   • 188 views
   • 
   • crazy^millman
   • April 18

10. n_tpln_mch - what is its possible values?

    By Giang-TT, February 14
    • 19 replies
    • 984 views
    • 
    • Colin Gilchrist
    • April 18

11. Tap with Peck

    By VK-8, April 17
    • 2 replies
    • 134 views
    • 
    • H.tom
    • April 18

12. post expire

    By MSL, January 14, 2016
    • 5 replies
    • 1.3k views
    • 
    • BehindYou
    • April 16

13. T-value modification

    By Ken Do, March 22
    • 1 reply
    • 216 views
    • 
    • crazy^millman
    • April 11

14. MPmaster not posting A- values ?

    By DEFAULT802, March 26
    • 1 reply
    • 205 views
    • 
    • DEFAULT802
    • March 26

15. how to make drilling to do canned cycle( G83)

    By MSL, September 30, 2011
    • 12 replies
    • 9.7k views
    • 
    • GORAN KRZNAR
    • March 19

16. Haas TR-160Y Trunnion Table

    By MSL, September 18, 2012
    • 16 replies
    • 5.8k views
    • 
    • space7737
    • March 14

17. Postblock for computer name or mac address

    By lim-mazak, March 9
    • 3 replies
    • 297 views
    • 
    • Colin Gilchrist
    • March 13

18. How to limit number line output or file size in NC file

    By lim-mazak, March 9
    • 3 replies
    • 303 views
    • 
    • Colin Gilchrist
    • March 11

19. Mastercam won't open to the post I set it to

    By mrohnymuso, March 9
    • 1 reply
    • 220 views
    • 
    • JParis
    • March 9

20. ADDING TOOL LIST TO HEADER

    By ALeX CaSTro, December 14, 2020
    • 3 replies
    • 1k views
    • 
    • JParis
    • March 1

21. Spacing

    By djspano12, February 20
    • 2 replies
    • 322 views
    • 
    • djspano12
    • February 23

22. LATHE INSERT INFO

    By mirek1017, July 31, 2023
    • 8 replies
    • 831 views
    • 
    • BehindYou
    • February 18

23. How to know parameter number

    By eltklas, February 15
    • 2 replies
    • 315 views
    • 
    • eltklas
    • February 15

24. G-Code as Binary output

    By BehindYou, February 14
    • 0 replies
    • 334 views
    • 
    • BehindYou
    • February 14

25. 5 Axis Fanuc Generic post question: Primary axis does not reset on Top Plane

    By Giang-TT, January 17
    • 6 replies
    • 698 views
    • 
    • crazy^millman
    • February 14