317 replies to this topic

[volsfan]

Thanks but no attachment. I tried copying it but will try the admin mode

[Josh Kinney - ProCNC]

Try the last link I put up.

Josh-

[volsfan]

Thanks Josh. I can open yours but still not mine. I also DL the lang.dll for X4 and X3 from GMCCS website and I could open the X4 alng.dll but not for X3 and that is what I am running (yes we are way behind on updates)I wonder what the differences is

[volsfan]

ok i figured out my issue. The dll was compressed so I had to uncompress it with UPX exe compressor and now I can edit it

[paulf]

.

[paulf]

There are many pages on this topic- so the answer may already be there- but my q is:- when i do a tool list with x+ can i edit it to show just certain bits of info- there is too much info shown at present- can i put custom info in for each tool or is all taken from tool def ?- thanks

[dieseltruck]

lost the x+ tool list default program with the  inventor 2013 installation
and selected  adobe reader to open it( too early in the morning and no coffee) now I cannot open my tool list    please advice  running  windows 7  
thank you

[TuxedoMask]

Thanks Gunther!

I saw this posted back a couple pages and didn't see an answer. I was wondering if there was a way for X+ not to duplicate tools when I select a whole toolpath group? Right now to get around that I'm selecting each new tool for X+ to post out.

Thanks in advance!

[dieseltruck]

dieseltruck, on 21 May 2012 - 10:34 AM, said:

lost the x+ tool list default program with the  inventor 2013 installation
and selected  adobe reader to open it( too early in the morning and no coffee) now I cannot open my tool list    please advice  running  windows 7  
thank you

please ignore this question,  it was mastercam corrupted file.
saved under different name and it was all good again.

[Hub]

Where do you get X+ for Mastercam X6?

[peon]

Hub, on 31 May 2012 - 10:54 AM, said:

Where do you get X+ for Mastercam X6?

Please read the first post in this thread.

[Günther Massimo - GMCCS]

New version of X+ is available.
Please read further information on my web page.
Rename NCI is available now.

[Jmick]

Thank you Gunther for the update. The addition of the tp groupname was much appreciated. I am having problem though.I have several toolpath groups
in one machine group and no matter which toolpath group I select the first toolpath group name is the one that appears. Any Ideas?

[Larry1958]

Followed link but cant find X4 version for English. Am I missing something? Does this work with Lathe?

[Sumac Andy]

I have just ventured into using multiple toolpath groups, and the problem I am having is this...
I have 3 groups, OP1, OP2 and OP3.
When I try to do a setup sheet for the individual ops I only get OP3 showing in the description block at the top of the page.
I have tried re-arranging the groups so OP1 is after OP3 but still only get the information of OP3 in OP1 setup?
Any one else get this?  Have I missed something here?
So far these setup sheets have proved a time saving and paper saving so am well pleased with the software so far.

Andy.

[Larry1958]

Cant find X4 english???

[shazam/TPP]

If memory serves me right, there is no X+ for X4 lathe just mills

[Günther Massimo - GMCCS]

Jmick, on 11 June 2012 - 01:39 PM, said:

Thank you Gunther for the update. The addition of the tp groupname was much appreciated. I am having problem though.I have several toolpath groups
in one machine group and no matter which toolpath group I select the first toolpath group name is the one that appears. Any Ideas?

It's actually the name of the active group. Just make the group active. Pull the red arrow in the specific group.

[Jmick]

That did it. Thanks

[Sumac Andy]

Günther Massimo - GMCCS, on 12 June 2012 - 02:54 PM, said:

It's actually the name of the active group. Just make the group active. Pull the red arrow in the specific group.

Thanks, that works brilliant