Coolant off on retract (milling)

[Mic6]

Hey Guys,

     How do I set my coolant to turn off upon retract to feed plane when milling, although it works fine drilling.  I used the debugger but I couldn't get the M9 to stick.  Maybe "scoolant"?

 

TIA!

O1111 (8606799-901-1)
(T1   - 1 INCH DRILL         - H1   - D1   - D1.0000")
G00 G17 G20 G40 G80 G90
G91 G28 Z0.
(DRILL 1ST DEPTH ENTRY HOLE)
N1 T1 M06 (1 INCH DRILL)
(MAX - Z.1)
(MIN - Z-3.9004)
G00 G17 G90 G54 X0. Y0. S477 M03
G43 H1 Z.1
/M8
G00 Z.1
G94
G99 G83 Z-3.9004 R.1 Q.15 F4.77
G80 M9   <--------------------------------SWEET
M05
G91 G28 Z0.
G90
G154 P99 X0 Y0
T1 M6
M30
%

O1111 (8606799-901-1)
(T6   - 3/8 BULL ENDMILL 0.01 RAD - H6   - D6   - D0.3728" - R0.0100")
G00 G17 G20 G40 G80 G90
G91 G28 Z0.
(ROUGH O-RING DETAIL A)
N6 T6 M06 (3/8 BULL ENDMILL 0.01 RAD)
(MAX - Z.25)
(MIN - Z-.047)
(Z STOCK TO LEAVE  = .005)
(XY STOCK TO LEAVE = .005)
G00 G17 G90 G54 X1.8882 Y-.2636 S5000 M03
G43 H6 Z.25
/M8
Z.1
G94 G01 Z-.047 F60.
G41 D6 X2.02 Y-.1318 F45.
G03 X2.0746 Y0. I-.1318 J.1318
X0. Y2.0746 I-2.0746 J0.
X-2.0746 Y0. I0. J-2.0746
X0. Y-2.0746 I2.0746 J0.
X2.0746 Y0. I0. J2.0746
G01 Y.005
G03 X2.0197 Y.1367 I-.1864 J-.0004
G01 G40 X1.8876 Y.2682
G00 Z.25      <--------------------------------------Would like M9 here.
M05
G91 G28 Z0.
G90
G154 P99 X0 Y0
T6 M6
M30

[PcRobotic]

I have the same issue too.

[crazy^millman]

Mic, what post are you using? What coolant process are you using? Are you using the old school process or the new process?

[Mic6]

Hey Ron, thanks for the reply.  I'm using the MPMaster shown below.  As for Coolant process, I'm unsure.

 

 

 

[MIL-TFP-41]

I think what Ron is getting at...are you using the "X" style coolant or the old style? Do have to options of "before, with, after" when turning on your coolant (X style) or just On/Off?

[Mic6]

Oh, just On/Off.  Although I tried an MP Master MD which used X-Style, and I tried using the de-bugger to pin down where the M9 was located, but it didn't work out very how I wanted.  Also, I don't like all those coolant options, just On or Off in the locations I prefer.    Thanks for the clarity on the coolant styles MIL

[MIL-TFP-41]

in your pretract section...find this

 

      pbld, n$, sgabsinc, sgcode, [if gcode$ = 1, sgfeed], *sg28, "Z0.", [if gcode$ = 1, feed], scoolant, e$

 

change to

 

scoolant, e$
pbld, n$, sgabsinc, sgcode, [if gcode$ = 1, sgfeed], *sg28, "Z0.", [if gcode$ = 1, feed], e$

 

Should get you pretty close

[Mic6]

Thanks, I'll give it a shot and report back

[Mic6]

Hmm, no change.  Turns off on retract from Milling OPs.  No M9 for drilling OPs