Mastercam X8 Mill Level 3 eCourse

Buy Now
149.00 995.00

This eCourse is designed to provide the resources you need to become proficient with 3D geometry creation and toolpaths. If you are new to Mastercam, it is highly recommended that you start with Mill Level 1 (book or eCourse) to build a firm foundation of 2D knowledge prior to exploring 3D.

Below you will find an overview of the eCourse video content organized by tutorial and respective video segments. Each tutorial will walk you through creating geometry, applying then verifying toolpaths and generating G-Code for a machinable part. This course will take approximately 15 hours to complete.

Note: The free home learning edition/demo software for this course has expired. You can still watch the videos and read the eBook but you will not be able to follow along unless you own a licensed version of Mastercam.

Introduction
  1. Getting Started (Mastercam Workspace)
    3:31
Tutorial 1
  1. Tutorial 1 covers Surface Rough Pocket, Surface Finish Shallow & Surface Finish Contour toolpaths. 

  2. 1 - Geometry Creation
    2:28
  3. 2 - Surface Creation
    5:47
  4. 3 - Fixture, Tool List and Stock Setup
    1:32
  5. 4 - Rough the Part using Surface Rough Pocket
    4:50
  6. 5 - Backplot and Verify the Toolpaths
    5:07
  7. 6 - Finish Using Surface Finish Shallow
    5:37
  8. 7 - Finish the Walls Using the Contour Toolpath
    4:08
  9. 8 - Post the File
    1:26
Tutorial 2
  1. Tutorial 2 covers Surface Rough Pocket, Surface Finish Parallel & Surface Finish Pencil toolpaths.

  2. 1 - Geometry Creation
    5:12
  3. 2 - Surface Creation
    3:47
  4. 3 - Fixture, Tool Settings and Stock Setup
    1:12
  5. 4 - Rough using Surface Rough Pocket
    3:08
  6. 5 - Finish using Surface Finish Parallel
    3:56
  7. 6 - Clean Corners using Surface Finish Pencil Toolpath
    4:20
Tutorial 3
  1. Tutorial 3 covers Stock Model, Surface HS Rest Roughing & Radial & Surface Finish Blend toolpaths.

  2. 1 - Import and Manipulate Part
    3:50
  3. 2 - Fixture, Tool List and Stock Setup
    1:54
  4. 3 - Roughing Toolpath using Rest Roughing
    9:11
  5. 4 - Set Stock Model from Rough Operation
    0:43
  6. 5 - Finish one side using HS Radial
    4:36
  7. 6 - Finish using Surface Blend
    3:43
  8. 7 - Transform Rotate and Post
    3:36
Tutorial 4
  1. Tutorial 4 covers Surface HS OptiArea, Surface HS OptiRest, Surface HS Hybrid & Surface HS Scallop toolpaths.

  2. 1 - Import the STP file
    2:37
  3. 2 - Fixture, Tool List and Stock Setup
    0:55
  4. 3 - Rough the part using OptiArea
    3:07
  5. 4 - Set Stock from Rough Operation
    0:23
  6. 5 - Cleanup using OptiRest
    3:37
  7. 6 - Set another Stock Model
    0:26
  8. 7 - Finish using HS Hybrid
    3:30
  9. 8 - Use Check Holder and Post
    1:47
Tutorial 5
  1. Tutorial 5 covers Surface HS Core Roughing, Scallop, Spiral & Waterline toolpaths.

  2. 1 - Geometry and Sufrace Creation 1
    7:38
  3. 2 - Geometry and Sufrace Creation 2
    7:46
  4. 3 - Fixture, Tool List and Stock Setup
    1:09
  5. 4 - Rough the Part using HS Core Roughing
    4:04
  6. 5 - Set the Stock Model
    0:28
  7. 6 - Finish one Pocket using HS Scallop
    2:26
  8. 7 - Transform Rotate the Toolpaths
    1:14
  9. 8 - Finish the top using HS Sprial
    6:22
  10. 9 - Finish the walls using HS Waterline
    6:50
Tutorial 6
  1. Tutorial 6 covers Surface HS OptiCore, Horizontal, Waterline, Raster & Pencil toolpaths.

  2. 1 - Open the MCX-8 File and Create Surfaces
    4:18
  3. 2 - Fixture, Tool List and Stock Setup
    1:04
  4. 3 - Rough the Part using HS OptiCore
    2:48
  5. 4 - Set the Stock Model for the Rough Operation
    0:31
  6. 5 - Finish the Flat Areas using HS Horizontal
    2:06
  7. 6 - Finish the Walls using HS Waterline
    2:27
  8. 7 - Finish the Shallow Area using HS Raster
    2:41
  9. 8 - Finish Sharp Corners with HS Pencil
    3:22
Tutorial 7
  1. Tutorial 7 covers Surface HS OptiArea, Rest Roughing, Surface Finish Scallop, Leftover & Project toolpaths.

  2. 1 - Open File and Create Surfaces
    8:35
  3. 2 - Fixture, Tool Settings and Stock Setup
    0:59
  4. 3 - Rough out the Part using OptiArea
    1:33
  5. 4 - Clean Remaining Areas using HS Rest Roughing
    2:01
  6. 5 - Set the Stock Model from the Rough Operation
    0:28
  7. 6 - Finish the Area using Scallop
    5:35
  8. 7 - Finish the Area using Surface Finish Leftover
    2:47
  9. 8 - Pocket Toolpath
    1:03
  10. 9 - Engrave Toolpath using Project
    3:07

Reviews



Raja Singh

  • 5
   1 of 1 member found this review helpful 1 / 1 member

Great Knowledge

Share this review


Link to review

Join us!

eMastercam - your online source for all things Mastercam.

Together, we are the strongest Mastercam community on the web with over 56,000 members, and our online store offers a wide selection of training materials for all applications and skill levels.

Follow us