Mastercam 2019 Mill Essentials eCourse

Buy Now

149.00 995.00

This course is designed to familiarize you with the Mastercam user interface (UI) and provide the resources you need to become proficient with 2D geometry creation and toolpaths. If you are new to Mastercam, it will help you quickly develop your Mastercam skill set; if you are already using the software, (perhaps an older version) it will get you up-to-date and enhance your abilities.

Below you will find an overview of the eCourse video content organized by tutorial and respective video segments. Each tutorial will walk you through creating geometry, applying then verifying toolpaths and generating G-Code for a machinable part. This course will take approximately 13 hours to complete.

All videos in the eCourse are Closed Captioned

Introduction

Mastercam 2019 Workspace

8:29

Tutorial 1

Tutorial 1 covers Facing, Circle Mill, Contour, Spot Drill, and Drill Toolpaths.
Geometry Creation

5:36
Machine Definition and Stock Setup

3:01
Face the Part

2:48
Circle Mill the Large Hole

6:35
Circle Mill the Inner Hole

3:07
Spot Drill the Four 1/4 Inch Holes

3:19
Drill the Four 1/4 Inch Holes

2:14
Chamfer the Large Hole

3:01
Machine the Chamfers at the Corners Using Contour

2:45
Post

0:57

Tutorial 2

Tutorial 2 covers Multiple Setups, Slot Mill, Pocket, 2D High Speed Dynamic Mill, and Contour Toolpaths
Geometry Creation

9:37
Machine Definition and Stock Setup

1:08
Slot Mill

4:18
Pocket Toolpath to Machine the Cutouts

3:16
Finish the Inside Shapes Using 2D High Speed Dynamic Contour

4:35
Rough the Outside Using High Speed Dynamic Mill

5:54
Finish the Outside Profile Using Contour

1:60
Create a New Setup to Machine the Bottom

4:35
Face the Bottom of the Part

2:25
Post

1:36

Tutorial 3

Tutorial 3 covers 2D High Speed Area Mill, 2D High Speed Dynamic Mill, Pocket, Pocket Remachining Toolpaths
Geometry Creation

10:28
Machine Definition and Stock Setup

1:07
2D High Speed Area Mill

5:52
2D High Speed Dynamic Mill to Machine the Lower Step

4:40
Pocket Toolpath to Remove the Material in the Inner Ellipse

4:13
Pocket Remachining to Clean Out the Letters

3:07
Post

0:35

Tutorial 4

Tutorial 4 covers 2D HS Dynamic Mill, Contour, Area Mill, and Toolpath Transform
Wireframe Creation

14:30
Solids Creation

7:24
Machine Definition and Stock Setup

1:15
2D High Speed Dynamic Mill to Machine the Top of the Part

4:40
Finish the Walls Using a Contour Toolpath

3:01
Area Mill to Machine One of the Pockets

3:20
Toolpath Transform to Machine the Remaining Pockets

2:05
Finish the Picket Walls Using a Contour Toolpath

2:37
Spot Drill and Drill the Two Holes

4:36
Chamfer the Outer Diameter

2:47
Chamfer the Pockets

3:02
Create a Second Setup to Machine the Bottom

1:59
Dynamic Mill to Remove the Material Inside the Bottom of the Part

2:49
Finish the Bottom Pocket Using a Contour Toolpath

1:59
Post

1:28

Tutorial 5

Tutorial 5 covers Multiple Setups, 2D High Speed Area Mill, Rest Mill, Spot Drill, Drill, Tap, Counterbore, and Slot Mill
Open the SolidWorks File

1:47
Machine Definition and Stock Setup

0:55
2D High Speed Area Mill to Machine the Upper Step

3:05
Copy the Previous Operation to Machine the Pocket

3:05
Area Mill to Remachine the Remaining Material

2:31
Spot Drill and Drill the Holes

4:11
Tap the Holes

1:42
Create a New Toolpath Group, Change the NC File Name, and Change the WCS

1:23
Spot Drill the Three Holes

3:08
Drill the Two 3/8" Tapped Holes

1:59
Tap the Two 3/8" Tapped Holes

1:44
Drill the Large Hole

1:51
Counterbore the 1/2" Hole With a Flat Endmill to Make a Flat Bottom Hole

1:49
Change the WCS to Machine the Left Side Slot

1:18
Slot Mill

2:11
Rename the NC File for Setup #3 and Post the Files

0:56

Tutorial 6

Tutorial 6 covers High Speed Dynamic Mill, 2D High Speed Area Mill, 2D High Speed Blend Mill, and 2D High Speed Peel Mill Toolpaths.
Geometry Creation

8:24
Machine Definition and Stock Setup

0:47
High Speed Dynamic Mill

3:48
2D High Speed Area Mill to Machine the Step

2:42
2D High Speed Blend Mill

3:33
2D High Speed Peel Mill

4:28
Post

0:37

Tutorial 7

Tutorial 7 covers 2D High Speed Dynamic Mill, FBM Drill, Dynamic Mill, Pocket, and Contour Toolpaths
Wireframe Creation

8:00
Solid Creation

4:23
Machine Definition and Stock Setup

0:55
2D High Speed Dynamic Mill

2:59
FBM Drill

7:09
Dynamic Mill the Outside Profile

3:44
Pocket Toolpath

2:41
Contour to Finish the Outside Profile

1:60
Post

0:33

Exercises

Exercises
Analyze Chains

4:48
Analyze Commands

3:54
Break Commands

1:32
Chaining

4:43
Create Arc

2:09
Create Arc Tangent

2:15
Create Fillet

1:36
Create Line

2:49
Create Line Tangent

1:29
Create Point

2:23
Create Rectangle

2:24
Join

1:46
Managing Attributes and Levels

6:21
Transform Mirror

1:36
Transform Offset

2:46
Transform Rotate

1:19
Transform Translate

1:60
Trim

1:32

Write a review

Your name
Rating Required

1 2 3 4 5
Comment Required
Click here

× Pasted as rich text.   Paste as plain text instead

Only 75 emoji are allowed.

× Your link has been automatically embedded.   Display as a link instead

× Your previous content has been restored.   Clear editor

× You cannot paste images directly. Upload or insert images from URL.

Insert image from URL
×

Desktop

Tablet

Phone

Nick_ 0

January 8, 2019

4 of 6 members found this review helpful 4 / 6 members

Very well structured course! Love the fact that the speech is slow and clear ( and English accent ). That course cannot be compared to any other which you can find for free or in youtube.

I think it's a good idea to make the drawing in pdf file to download, so when you start your wireframe you can actually be guided by the drawing rather than the video.

I struggled with some wireframe geometry, so may be a good option if exercises training/tutorial is accessible at any time of the course, rather than being last.

I wish to see another tutorial based on recognizing feature, where different features of 3D object are shown and different methods of approaching discussed (area mill, dynamic mill, peel mill, blend mill, etc).

Great work! Amazing Essential training! Amazing basis to build on!

Regards,

Nick

Share this review

Link to review

Join us!

eMastercam - your online source for all things Mastercam.

Together, we are the strongest Mastercam community on the web with over 56,000 members, and our online store offers a wide selection of training materials for all applications and skill levels.