53,326 topics in this forum

1. X Verify 1 2 3 4 8

   By Harry Morse, November 30, 2004
   • 183 replies
   • 12.3k views
   • 
   • steve f
   • December 6, 2004

2. The New 2017 Interface 1 2 3 4 6

   By John Hill @ Poplar Hill Machine, July 18, 2016
   • 125 replies
   • 12.3k views
   • 
   • bad-mod
   • September 12, 2016

3. Drawing Lathe Tools

   By Randy Morton @ Clem Industrial, May 20, 2008
   • 6 replies
   • 12.2k views
   • 
   • crazy^millman
   • November 23, 2016

4. G41/G42 ERROR problem

   By Buddy J, August 26, 2011
   • 6 replies
   • 12.2k views
   • 
   • Buddy J
   • August 26, 2011

5. Tapping 304 stainless steel

   By Smit, August 24, 2001
   • 9 replies
   • 12.2k views
   • 
   • Chips Ahoy
   • August 28, 2001

6. Dynamic milling questions 1 2

   By MACHINING JIM, December 13, 2011
   • 33 replies
   • 12.2k views
   • 
   • MACHINING JIM
   • December 16, 2011

7. Mastercam X5 64 bit

   By StainlessSteel, May 4, 2011
   • 9 replies
   • 12.2k views
   • 
   • Pete Rimkus from CNC Software Inc.
   • May 9, 2011

8. fanuc wire subprogram post

   By fuzzy71e, March 11, 2008
   • 17 replies
   • 12.2k views
   • 
   • Guest
   • March 12, 2008

9. kitamura or okuma? 1 2

   By cherokeechief79, August 9, 2012
   • 40 replies
   • 12.1k views
   • 
   • cherokeechief79
   • September 1, 2012

10. Tool libraries for Mastercam

    By Reijo Heurlin from Zenex Finland, April 29, 2010
    • 15 replies
    • 12.1k views
    • 
    • hot_chip
    • August 26, 2010

11. Peck Tapping using Mastercam

    By mike561h, January 18, 2008
    • 20 replies
    • 12.1k views
    • 
    • ikertx0
    • June 29, 2023

12. 4th axis

    By Santa Fe, July 16, 2008
    • 7 replies
    • 12k views
    • 
    • Santa Fe
    • July 17, 2008

13. G68.2 & G54.4 1 2

    By So not a Guru, November 2, 2015
    • 28 replies
    • 11.9k views
    • 
    • So not a Guru
    • November 13, 2015

14. calculating chamfer depths

    By Camdude®, April 22, 2008
    • 14 replies
    • 11.9k views
    • 
    • crazy^millman
    • February 29

15. Mastercam X6 Probe 1 2

    By Rocketmachinist, November 28, 2011
    • 39 replies
    • 11.9k views
    • 
    • BenK
    • November 30, 2011

16. Researching CMM options, any advice?

    By Bob W., March 31, 2014
    • 21 replies
    • 11.9k views
    • 
    • Chipmakr
    • April 3, 2014

17. Active Reports 1 2

    By ToddF, December 24, 2011
    • 40 replies
    • 11.8k views
    • 
    • PMDc
    • February 24, 2013

18. rigid tapping - G94 or G95??? 1 2

    By BuxtonMachine, May 6, 2006
    • 38 replies
    • 11.8k views
    • 
    • BuxtonMachine
    • May 10, 2006

19. Mastercam X8 processing slow 1 2

    By harishkumarchandra, January 31, 2015
    • 28 replies
    • 11.8k views
    • 
    • jt300zx
    • June 30, 2015

20. Toolbars Missing 1 2

    By SpecialtyTool, April 18, 2016
    • 25 replies
    • 11.8k views
    • 
    • SpecialtyTool
    • April 26, 2016

21. Haas VF4 Question

    By Jim at Gentex, December 11, 2008
    • 20 replies
    • 11.8k views
    • 
    • mkd
    • February 16, 2012

22. MasterCam vs Esprit

    By Mcam Nut, August 20, 2010
    • 12 replies
    • 11.8k views
    • 
    • Guest
    • August 21, 2010

23. Received MasterCAM X today--yahoo 1 2 3 4 10

    By Code_Breaker, August 1, 2005
    • 248 replies
    • 11.7k views
    • 
    • londoner
    • August 29, 2005

24. X9 installation error

    By Nils N, July 15, 2016
    • 12 replies
    • 11.7k views
    • 
    • JoshC
    • January 27, 2021

25. Machine Simulator 1 2 3

    By DavidB, September 28, 2017   

    • umc 750
    • 72 replies
    • 11.6k views
    • 
    • sir Camalot
    • July 2, 2020