2,726 topics in this forum

1. figure chip thinning 1 2

   By rgollar, February 22, 2011
   • 48 replies
   • 55.1k views
   • 
   • GARRJESS
   • February 2, 2023

2. .001 positional tolerance

   By ujmujm, March 13, 2017
   • 16 replies
   • 2.9k views
   • 
   • Leon82
   • May 13, 2017

3. .018 holes through 304 ss tubing

   By buck30, January 21, 2011
   • 5 replies
   • 1.9k views
   • 
   • Dave.L
   • January 25, 2011

4. .050 ball endmill .025 deep for miles

   By left coast lefty, February 8, 2013   

   • need advice for optimization
   • 10 replies
   • 2.2k views
   • 
   • Matthew Hajicek - Singularity
   • February 11, 2013

5. .063 1.9 deep in 304

   By GoetzInd, March 21, 2013   

   • Any drill suggestions?
   • 7 replies
   • 1.4k views
   • 
   • GoetzInd
   • March 31, 2013

6. .125 hole 3" deep

   By MIL-TFP-41, January 27, 2014
   • 4 replies
   • 1.2k views
   • 
   • Bwank1124
   • January 29, 2014

7. .1875 HOLE 8 INCHES DEEP IN ALUMINUM

   By Pgreenlaw, December 2, 2021
   • 6 replies
   • 1k views
   • 
   • Pgreenlaw
   • December 13, 2021

8. .490 radius round over

   By jas6142, April 30, 2012
   • 7 replies
   • 1.5k views
   • 
   • kh012
   • April 30, 2012

9. .500" ball mill x 8.00 oal....carbide

   By kkominiarek, June 1, 2012
   • 5 replies
   • 1.6k views
   • 
   • LA CAMmer
   • June 8, 2012

10. .igs to G code 1 2

    By bobberserker, November 13, 2012
    • 42 replies
    • 16.2k views
    • 
    • FROZEN
    • November 3, 2014

11. .mcx9 file

    By G1CNC, September 27, 2020
    • 4 replies
    • 1.1k views
    • 
    • Matthew Hajicek - Singularity
    • October 1, 2020

12. .tooldb File Format??

    By crazy^millman, January 17, 2014   

    • What can we edit it in?
    • 6 replies
    • 4k views
    • 
    • crazy^millman
    • January 17, 2014

13. "Drivers Not Loaded" Error mesage on Haas tool room mill

    By Brad St., August 26, 2021
    • 1 reply
    • 916 views
    • 
    • RemiB
    • October 21, 2022

14. "h" tool length offsets 1 2

    By zappafanx, January 6, 2017   

    • 18i-M
    • 38 replies
    • 4k views
    • 
    • Sticky
    • January 11, 2017

15. "Too many digit" Alarm

    By Tinger, August 21, 2019
    • 15 replies
    • 3.2k views
    • 
    • Leon82
    • September 26, 2019

16. (Question) Selective insert changing

    By randy5061, May 4, 2023   

    • question
    • 5 replies
    • 456 views
    • 
    • huskermcdoogle
    • May 8, 2023

17. #3 Top Notch Insert Model

    By Dave Ball, April 15, 2011
    • 0 replies
    • 1.7k views
    • 
    • Dave Ball
    • April 15, 2011

18. #3006 message with manual guidei

    By Leon82, October 23, 2019
    • 20 replies
    • 3.6k views
    • 
    • Leon82
    • March 3, 2020

19. $1million to the Okuma Guru that can answer this!!!

    By mkd, May 21, 2015
    • 16 replies
    • 4.4k views
    • 
    • mkd
    • July 27, 2015

20. 0.029" external grooving tool

    By So not a Guru, August 31, 2021
    • 3 replies
    • 566 views
    • 
    • huskermcdoogle
    • August 31, 2021

21. 1 1/4 -4 stub acme double lead ext threads

    By Howard jones, February 7, 2020
    • 0 replies
    • 289 views
    • 
    • Howard jones
    • February 7, 2020

22. 1 1/4 -4 stub acme double lead ext threads

    By Howard jones, February 7, 2020
    • 0 replies
    • 314 views
    • 
    • Howard jones
    • February 7, 2020

23. 1 1/4 -4 stub acme double lead ext threads

    By Howard jones, February 7, 2020
    • 4 replies
    • 613 views
    • 
    • #Rekd™
    • February 12, 2020

24. 1-12 UNJF chase die

    By So not a Guru, March 11, 2021
    • 3 replies
    • 552 views
    • 
    • Eric@HorsepowerInc.
    • March 11, 2021

25. 1-64 UNJC 3B TAPS

    By gms1, June 14, 2012
    • 2 replies
    • 1.9k views
    • 
    • rob@fain
    • June 15, 2012