Jump to content

Welcome to eMastercam

Register now to participate in the forums, access the download area, buy Mastercam training materials, post processors and more. This message will be removed once you have signed in.

Use your display name or email address to sign in:

Mill Advanced Exercise #3


khainguyen745
 Share

Recommended Posts

Hi,

Your 2d drawing is not correct, see the attached photo. The correct drawing is in RED and yours is in BLUE. 

The handle is created by creating arcs. The upper arc (5.5" Radius) is created using Arc Polar. Set the Radius to 5.5" and select the center of the Radius shown at the intersection of 6.75" in X and 4.375" down in Y for the center of the arc. Then create a 0.25" fillet between this arc and the horizontal line. Set the angles to 140 (Start) and 180 (Finish). Then create the lower 9.675 radius arc using the Arc Tangent command, have the method set to Arc One Point and set the radius to 9.675. Select the 5.5" arc created above as the tangetnt arc and then select the lower intersection of 0.75" in X and 6.0" down in Y as the point. Then select the arc you want to keep. Then trim the 5.5" arc to the 9.675" arc. Then create the 2.5" arc using Arc Polar again. Once you get this trimmed properly do an offset to create the other side of the handle.

You have a duplicate line in your file as well.

All of these techniques are shown in the Mill Advanced Tutorial 3, I assume this is an assignment for a college course if you do not have access to the tutorial?

 

Capture.JPG

  • Like 1
Link to comment
Share on other sites
18 hours ago, #Rekd™ said:

Hi,

Your 2d drawing is not correct, see the attached photo. The correct drawing is in RED and yours is in BLUE. 

The handle is created by creating arcs. The upper arc (5.5" Radius) is created using Arc Polar. Set the Radius to 5.5" and select the center of the Radius shown at the intersection of 6.75" in X and 4.375" down in Y for the center of the arc. Then create a 0.25" fillet between this arc and the horizontal line. Set the angles to 140 (Start) and 180 (Finish). Then create the lower 9.675 radius arc using the Arc Tangent command, have the method set to Arc One Point and set the radius to 9.675. Select the 5.5" arc created above as the tangetnt arc and then select the lower intersection of 0.75" in X and 6.0" down in Y as the point. Then select the arc you want to keep. Then trim the 5.5" arc to the 9.675" arc. Then create the 2.5" arc using Arc Polar again. Once you get this trimmed properly do an offset to create the other side of the handle.

You have a duplicate line in your file as well.

All of these techniques are shown in the Mill Advanced Tutorial 3, I assume this is an assignment for a college course if you do not have access to the tutorial?

 

Capture.JPG

Hello Sir,

Thank you so much for helping me. This is not for college classes. I do it to kill time because of the current event. I understand how to do it now.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.

Join us!

eMastercam - your online source for all things Mastercam.

Together, we are the strongest Mastercam community on the web with over 56,000 members, and our online store offers a wide selection of training materials for all applications and skill levels.

Follow us

×
×
  • Create New...