feed per-revolution

[Metric]

Hello friends,

Is there switch on the post to post out feed rate per revolutions? My company just switch to Mastercam from Gibbscam last week. So I have to learn  to minor modify post to have some program to to test run  in the mean time waiting to order all posts.

Best regards.

Metric

 

[Alex Dales]

What is the post/machine?

If you are using an MPMASTER you can set the feedrate to Unit per Rev with Misc Integer #6 in the toolpath parameters.

 

[Metric]

Hi Alex.

Thank you. Happy thanksgiving

Metric

[Metric]

Hello Alex,

I don't see the Misc Integer #6 indicate Unit/rev on my post .  We have Okuma on our shop and use the Okuma OSP5020M 4X Mill.post for. Any idea?

Best regards.

Metric.

[crazy^millman]

33 minutes ago, Metric said:

Hello Alex,

I don't see the Misc Integer #6 indicate Unit/rev on my post .  We have Okuma on our shop and use the Okuma OSP5020M 4X Mill.post for. Any idea?

Best regards.

Metric.

Where did you get the post? It is a pretty basic post mod. Get a hold of your dealer and they should be ableto get it sorted out for you.

[Metric]

Hi C^Millman,

I got the post from MC 2018 installation disc. I will call them to get some help.

Thanks.

Metric

[Metric]

Hello Friends,

Please give some help. My dealer guy said i have to contact Inhousesolution to get help!!!. "For any post modifications you will need to contact In House Solution at [email protected]".

Regards.

Metric.

P.S Alex please lend me a hand...

 

[Leon82]

You have to edit the tap cycle to output the ipr code

On the ptap line

[Metric]

Hi Leon82, 

Thank you for advise. I did put it to yes but look like it doesn't work

"tap_ipr      : yes$   #Do G84 tapping using IPR (G95) feed mode?" (is this line what do you mean?).

Regards.

Metric

[Leon82]

In the drill cycles.

There is one for tap

Looks like this

pbld, n$, g85 yada yada

Add it before

 

[Leon82]

You cAn put this before that line

 

pbld, n$, sg95, e$

 

There is usually a header before them

 

#---------

#drilling

#----------

[Metric]

Hello Leon82,

I was in that section but did not see any switch to change start from #OKUMA CANNED CYCLES 

.....

" ptap$            #Canned Tap Cycle (G74/G84)
      pdrlcommonb
      pg71out
      if tap_ipr,
        [
        feed = 1 / n_tap_thds$    #Calc the IPR feedrate
        pcan1, pbld, n$, "G95", e$ #Set for IPR feed mode
        tapping = yes$            #Flag that we are IN a G84 tapping cycle
        ]
      pcan1, pbld, n$, *sgdrill, pxout, pyout, pfzout, pcout,
        prdrlout, dwell$, *feed, pm53out, strcantext, e$
      pcom_movea "

Thanks for help.

Metric.

[Leon82]

For that to work you have to turn the flag on and it's in there somewhere.

 

Under the bracket you can add that line I posted and it will post it out. But if you use this for other machines it may not be desired.

So if you want to limp thru till you have a custom post you can make a copy for the okuma

[Metric]

Hello Leon82,

I was in that section but did not see any switch to change start from #OKUMA CANNED CYCLES 

.....

" ptap$            #Canned Tap Cycle (G74/G84)
      pdrlcommonb
      pg71out
      if tap_ipr,
        [
        feed = 1 / n_tap_thds$    #Calc the IPR feedrate
        pcan1, pbld, n$, "G95", e$ #Set for IPR feed mode
        tapping = yes$            #Flag that we are IN a G84 tapping cycle
        ]
      pcan1, pbld, n$, *sgdrill, pxout, pyout, pfzout, pcout,
        prdrlout, dwell$, *feed, pm53out, strcantext, e$
      pcom_movea "

Thanks for help.

Metric.

[Metric]

Hello Leon82,

I will try tomorrow,

Thank you very much for helping,

Regards.

Metric

[Alex Dales]

15 hours ago, Metric said:

Hello Friends,

Please give some help. My dealer guy said i have to contact Inhousesolution to get help!!!. "For any post modifications you will need to contact In House Solution at [email protected]".

Regards.

Metric.

P.S Alex please lend me a hand...

 

Metric,

Have you e-mailed us a version of your post yet? I have not come across it.

Once you send it in, I will add that logic in for you.

Alex

[Metric]

Good morning Alex,

I just sent to you the posts. Please help to add the logic.

Thanks a lots.

Metric.