Tried to upload an educational version 2017 file, and I get this message:

Anyone know why?

Thanks

Not sure how it works just yet, but Thank you, Thank you, Thank you!  

You should check out the Mill Trim toolpath.

 

HTH

Is there a way to remove the air passes out of this tool path?   Also, is there a way that to associate tool paths to the stock model that I don't know about?

Thanks!

AMF

COLD_END MASTER CURVE.MCX-7

Hello all,

Ok, so I was liking X9 until I tried to use a Core or Dynamic Core toolpath.  WTF!  

it used to be chain two boundaries and go.  I can't figure out how the hell to make it work. 

The toolpath I create cuts out the core. 

What is required to make Dynamic Mill work like the old Core?

Thanks!

Hello all,

I'm trying to stitch from the top down.  The toolpath starts at the bottom of the radius and works up.  How do I change this?

Thank you,

AMF

PART ONE.MCX-7

Wow!  You guys are awesome!  Thanks for the replies.
I copied the WCS and set z to the top of the bulb.   I ran a finish pass on the bulb just to make sure I had it right, and I don't.

Please run the verification.  It cuts the top of the bulb off.  

When I ran this part, I just programmed the bulb side as if it were another part.   I'm going back now trying to figure out the right way

to do things. 

Thanks guys!

INBOARD BEARING HOUSING2.mcx-8

Hello All,

I have attached a file I am working on in Lathe.  I don't know how to flip the part with the WCS so as to machine the bulb side.

Any help will be greatly appreciated.

AMF

INBOARD BEARING HOUSING Rev1.mcx-8

My bad.  Thanks!

I can't seem to find the FTP.   How would I navigate to it?

Thanks

Awesome!  Thanks Ken!

Is there another way to go from spin to pan,  like Alt+Middle mouse button used to do?

I edited the design.workspace  applook tag, and it fixed it. 

Thanks 

If I load another workspace, it fixes itself.  It happens when I go into design.    

I am not having any luck trying to find a post that outlines how to edit a text file to change the appearance.   Does anyone know where I could find that?

Thanks!    

It won't let me drag them.  

Hello All,

I don't know what I did to cause this, but my ribbon bar takes up most of the screen.  I don't know how to fix.   See attached picture.

Thanks!

Thanks guys!!!

How do you get to the customize right mouse click in X8?

Thanks!

Space Pilot it is.    Thank you!

Hello All,

I'm fixing to buy another 3d Mouse.    I have been getting along just fine with just the puck ( space navigator ).  I tried a space mouse pro, and I like it.  

I go to buy one and see this Space Pilot Pro for an extra $75.00.     Is the Space Pilot Pro worth the extra cash?   What do you guys think?

Thanks!

AMF

Yes the over engagement in corners = tool breakage is exactly what I'm referring to in the picture.  

Found it.  My apologies.

Wow, that seems really fast to me, but I'm going to give it a try.

Thanks Colin and JParis.

AMF

We haven't ran the part.  The part is steel, and we are anticipating trouble with this toolpath.  We are wanting to run full axial ( 1.00 DOC ), with a .875" carbide endmill.  I have generated just a core toolpath, and if it didn't retract constantly it is just what we want.  I have attached the file.   What do you think is the best option for this part? 

Thank you very much for your help!  

AMF

CORE.MCX-7

I'm having problems controlling the stepover amount in the corners of a dynamic core toolpath.  Please see the attached picture of the toolpath.  

How is this controlled?

Thanks!

AMF