50,616 topics in this forum

1. VERISURF TOOLS for 2020

   • 1
   • 2
   • 3
   • 4
   • 13

   By Verisurf - Ernie Husted, July 17, 2014   

   • verisurf tools
   • 306 replies
   • 125,832 views
   • 
   • Verisurf - Ernie Husted
   • 13 hours ago

2. X+ Mastercam 2019

   • 1
   • 2
   • 3
   • 4
   • 5

   By Günther Massimo - GMCCS, March 16, 2018   

   • x+
   • 2019
   • 109 replies
   • 37,704 views
   • 
   • vr6
   • Yesterday at 12:48 AM

3. Pitch in your little gems that make mcam life easier

   • 1
   • 2
   • 3
   • 4
   • 14

   By jlw™, November 2, 2015
   • 340 replies
   • 108,685 views
   • 
   • David Colin
   • April 2

4. Compensation Poll - Take the poll

   • 1
   • 2
   • 3
   • 4

   By Matthew Hajicek™ - Conventus, October 13, 2017
   • 78 replies
   • 31,977 views
   • 
   • mkd
   • March 4

5. ModuleWorks Help File - 08.2017

   • 1
   • 2

   By Guest, November 10, 2017
   • 41 replies
   • 21,625 views
   • 
   • So not a Guru
   • February 11

6. ProTip: How to set Control Definition Defaults

   • 1
   • 2

   By Colin Gilchrist, September 28, 2015   

   • defaults
   • Control Definition
   • (and 3 more)

     Tagged with:

     • defaults
     • Control Definition
     • Update
     • upgrade
     • tip
   • 38 replies
   • 42,542 views
   • 
   • Jen Yates
   • December 25, 2017

7. Important Topics - Please Read Before posting

   By Guest, May 31, 2012
   • 0 replies
   • 28,238 views
   • 
   • Guest
   • May 31, 2012

8. 3003-H14 Speeds & feeds

   By So not a Guru, 12 minutes ago
   • 0 replies
   • 3 views
   • 
   • So not a Guru
   • 12 minutes ago

9. help with a VERY deep pocket

   By cherokeechief79, 16 hours ago
   • 7 replies
   • 108 views
   • 
   • CADCAM3D5AXIS
   • 35 minutes ago

10. Learning How To Program an Impeller?

    By #Rekd™, Monday at 01:42 PM
    • 20 replies
    • 397 views
    • 
    • So not a Guru
    • 54 minutes ago

11. Move in ARC

    By johnr4mbo, 21 hours ago
    • 11 replies
    • 153 views
    • 
    • So not a Guru
    • 1 hour ago

12. Verisurf CMM Reviews Needed ( unbiased preferred )

    By Spotterhphc, 16 hours ago   

    • verisurf
    • cmm
    • (and 1 more)

      Tagged with:

      • verisurf
      • cmm
      • help
    • 2 replies
    • 49 views
    • 
    • So not a Guru
    • 1 hour ago

13. Error checking out Mill3D license

    By JB7280, 3 hours ago
    • 0 replies
    • 16 views
    • 
    • JB7280
    • 3 hours ago

14. Vericut Vue -On line for 2020-

    By Bill Craven, 16 hours ago
    • 0 replies
    • 33 views
    • 
    • Bill Craven
    • 16 hours ago

15. Very choppy movement with 3D Spacemouse

    By JB7280, yesterday at 10:43 AM
    • 2 replies
    • 101 views
    • 
    • JB7280
    • Yesterday at 01:21 PM

16. Creating letters question

    By danatoem, Tuesday at 02:57 PM
    • 7 replies
    • 156 views
    • 
    • danatoem
    • Tuesday at 10:12 PM

17. Mastercam over VPN

    By nevets, April 2
    • 16 replies
    • 422 views
    • 
    • JParis
    • Tuesday at 10:23 AM

18. Little x's and line with two points on it when drawing circle inside another

    By jeep534, Sunday at 02:52 AM
    • 4 replies
    • 192 views
    • 
    • jeep534
    • Tuesday at 02:22 AM

19. HOW TO PROGRAMME WITH MAX 3 DECIMAL

    By RICK PATEL, Friday at 09:17 PM
    • 3 replies
    • 201 views
    • 
    • RICK PATEL
    • Monday at 09:35 PM

20. Optirough and tilt holder to avoid gouge

    By Mikew8190, Sunday at 02:08 PM
    • 5 replies
    • 177 views
    • 
    • Aaron Eberhard - CNC Software
    • Monday at 03:53 PM

21. Hardware questions for Mastercam

    By Metallic, March 31
    • 10 replies
    • 286 views
    • 
    • Metallic
    • Monday at 04:35 AM

22. CIMCO Edit Integration for Mastercam

    By Elvincnc, March 5
    • 12 replies
    • 443 views
    • 
    • 5th Axis CGI
    • Sunday at 05:52 PM

23. HSM pack

    By pro grammer, April 3
    • 6 replies
    • 238 views
    • 
    • Greg Williams
    • Saturday at 12:40 AM

24. How to

    By Ramon George, March 29
    • 3 replies
    • 316 views
    • 
    • Ramon George
    • Friday at 05:38 PM

25. Multi axis drilling using saftey distance?

    By AWL304, April 3
    • 2 replies
    • 98 views
    • 
    • Leon82
    • April 3