Spacing

[djspano12]

Is there a way to have the g code post out like this?

 

Instead of not having an indent to make the g code look a little nicer and easier to read. Like how fusion 360 does. 

%
O00084 (PART)

G20

(TOOL - 1 OFFSET - 1)
(MDJNR164C  INSERT - DNMG433MS)
(FACE ROUGH)
G00 T0101
G18
M8
G97 S1798 M3
G00 G54 Z.01
X1.7
G50 S2000
G96 S800
G99 G01 X-.0938 F.007
G00 Z.11

(ROUGH PROFILE)
X1.3269
Z.2099
G01 Z.1099
Z-1.17
X1.4998
X1.6412 Z-1.0993
G00 Z.2099
X1.1538
G01 Z.1099
Z-1.17
X1.3269
X1.4683 Z-1.0993
G00 Z.2099
X.9806
G01 Z.1099
Z-1.17
X1.1538
X1.2952 Z-1.0993
G00 Z.2099
X.8075
G01 Z.1099
Z-1.17
X.9806
X1.122 Z-1.0993
M9
G00 G53 X0.
G53 Z0.
M01

(TOOL - 3 OFFSET - 3)
(3D LATHE TOOL-1  INSERT - INSERT)
(FACE FINISH)
G00 T0303
G18
M8
G97 S2000 M3
G00 G54 Z0.
X1.008
G50 S2000
G96 S790
G01 X-.0313 F.0065
G00 Z.1

(FINISH PROFILE)
X.7583
Z.0154
G01 Z-.0046
X.7783 Z-.0146
G03 X.7875 Z-.0256 R.0156
G01 Z-.6956
Z-.73
X.8261 Z-.7248
M9
G00 G53 X0.
G53 Z0.
M01

(TOOL - 5 OFFSET - 5)
(LATHE TOOL 3)
(SPOT)
G00 T0505
M8
G97 S2000 M3
G00 G54 Z.25
X0.
G99
G81 Z-.1 R.1 F.005
G80
M9
G53 X0.
G53 Z0.
M01

(TOOL - 16 OFFSET - 16)
(LATHE TOOL 4)
(.201 THRU HOLE)
G00 T1616
M8
G97 S2000 M3
G00 G54 Z.25
X0.
G99
G83 Z-.9904 R.1 Q0.05 F.005
G80
G00 Z.25
M9
G53 X0.
G53 Z0.
M01

(TOOL - 8 OFFSET - 8)
(1/4-20 RH TAP)
(.250-20 TAPPED HOLE)
G00 T0808
M8
G97 S500 M3
G00 G54 Z.25
X0.
Z.1
G84 Z-.8 R.1 E.05
G80
G00 Z.25 M3
M9
M5
G53 X0.
G53 Z0.
M01

(TOOL - 4 OFFSET - 4)
(0.3125 4 CENTER DRILL)
(SPOT .125 HOLES)
T0404
M154
M8
G97 P1500 M133
G98
G18
G00 G55 Z-.365 C0.
X1.1875
G241 X.3875 R.9875 F4.
C180.
G00 G80


(SPOT .250 HOLES)
X1.1875 Z-.1625 C90.
G241 X.4875 R.9875 F4.
C-90.
G00 G80
M9
M155
M135
G53 Y0.
G53 X0.
G53 Z0.
M01

(TOOL - 6 OFFSET - 6)
(0.25 1/4 JOBBER DRILL)
(.250 THRU HOLES)
T0606
M154
M8
G97 P1000 M133
G98
G18
G00 G55 Z-.365 C0.
X1.1875
G243 X-.9125 R.9875 Q0.05 F5.
G00 G80
M9
M155
M135
G53 Y0.
G53 X0.
G53 Z0.
M01

M00 (CHANGE .204 DRILL TO .125 DRILL)

(TOOL - 6 OFFSET - 6)
(0.125 1/8 HEAVY DUTY JOBBER DRILL)
(.125 THRU HOLES)
T0606
M154
M8
G97 P1500 M133
G98
G18
G00 G55 Z-.1625 C-90.
X1.1875
G243 X-.9125 R.9875 Q0.05 F2.
G00 G80
M9
M155
M135
G53 Y0.
G53 X0.
G53 Z0.
M01

(TOOL - 7 OFFSET - 7)
(NGDHR-16 - GC-4125  INSERT - GC-4125)
(FINISH FRONT RADIUS)
G00 T0707
G18
M155
M8
G97 S800 M3
G00 G54 Z-.751
X.9875
G50 S800
G96 S500
G99 G01 X.7875 F.003
G03 X.772 Z-.78 R.058
G00 X.8715
Z-.809
G01 X.6715
G02 X.772 Z-.78 R.058
G00 X.9875

(PART)
X1.408
Z-.809
G01 X1.208 F.001
X.185
X.385
G00 X.2
M9
M5
G53 X0.
G53 Z0.
M30
%

[Colin Gilchrist]

Sure.

Add:

*e$

To force a "blank line" in the NC Code output.

Add that code to the end of 'pheader$', 'psof$', 'ptlchg$', and 'ptlchg0$'.

[djspano12]

cool thanks for the reply