Mazak Intergrex

[Hymen]

Anyone here running one of these?

If yes, then could you possibly point out whats wrong with this code here. Transfer doesn't work properly, close but not quite right. I'm trying to fix a post for part transfer, but I don't have the working code. Or if you have some code that does part transfer in turning mode that you could share to help me out I'd be willing to give you my post work when it's done.

 

G28 U0

G28 W0

T1313.7

#500=20.

M202

M302

G0 X5.0266

Z-5.438

 

M202

M5 M305

G110 Z2

M306

G0 Z-#500

M544

M508 G98

G31 W-.1 F20.

M307

G4 X1.

M6

G1 W.1 F100.

M7

M302

M300

M360

M202

M153

M380

G97 S500 M3

X1.8788

G99

G1 X0.5 F.005

G0 X1.8788

X5.0266

 

G28 W0

G111

M545

M509

G50 W-#500

M300

M30

[IntegrexMan]

Here is code that I use to do a Part-off and Trasnfer. I use Z3 instead of Z2 because my machine has a lower turret and the Z for the lower turret is Z2 and the sub-spindle is now Z3. I am also not chucking a round part which is why there is a macro variable for the C2 sub-spindle position (#806). I also use macro varibles for the pull out amount as well (#827). Let me know if you have any questions.

 

 

( CUT-OFF )

N180

G30 U0. W0.

G53 G90

M212

M202 G98

G18

T0202.01 B4 (CUT OFF PART TO LENGTH)

G00 Z.0

M357

M302 (START SUBSPINDLE TRANSFER)

M201

G00 C0.0

M300

G112 M200

G110C2

G28H0

G0 C#806

M306 M540

G110Z3

Z[#826+15.] (SET SUB SPINDLE "Z" TO FIRST POSITION TO CLAMP PART)

G1 W-15. F150.

G112 M202

M506

M509 M541

G00 Z[#826+#827] (SET SUB SPINDLE "Z" PULLOUT FOR CUTOFF POSITION)

M07

G111

M302

T0202.01

G50 S1600

M511

G99

G96 S33 M3

M153 M8

G00 Z.5 (CUT OFF PART TO LENGTH)

X20.

G01 X-.2 F.06

X20. F.5

G30 U0

M5 M154 M9

M518 M512

M01

G110 Z3

G00 Z0.0

G111

G30 W0 Y0

M01

[Hymen]

Thanks will do!!

[Hymen]

Does anyone have the parameter file which turns on B-axis in the cview c-hook.

For both version 9 and X.

If so could you email it to me Please! and thank you!

[Hymen]

Hey Integrexman what info do I need in the set up page to run your code? I have adjusted some of the code, Z3 to Z2 and travels, to work with the 100sy I'm fixing the post for. Tried to run it but sub spindle traveled in the wrong direction. DOH!

[tryon]

for V9 open up the CVIEW.PRM file that is in your chooks folder and change the number after "1." to a "1", its probably a zero now. Dont know if its the same in X

[Hymen]

Thanks Tryon!

[IntegrexMan]

Hymen,

 

The only thing I can think of is that you need to set the macro varibles. #826 should be a negative number. This is the position the sub-spindle will be at to pick off you part. #827 is a positive number. This number is for the pull out amount of your stock. There should be no information in the set-up screen, that is only for when you are using mazatrol programming.

[Hymen]

So now I have the pick off working properly!

Thank you guys!

Now I am having a problem drilling at an angle (120deg B-Axis) on the sub. There is no problems on the main. I can turn on the sub fine, but approach/positioning for drilling is off.

I did find out that (#500 - sub over amout) needed to be in the value of S, on the G125/G128 line. Is "S" for positioning of the tool tip?

So I was hoping someone with an Integrex could post this file, only 1 drilling sequence needed, So I could try and configure something faster from the pieces I have. Any help appreciated

 

click Here for the .MCX