File not Found FANUC 31i

[dracksed]

Hi,

I am trying to transfer Macros with USB key into my AWEA 3016 using FANUC 31i controller. I successfully transfer 10 programs and when I try to transfer this following program into the CNC_MEMORY, instead of showing TRANFER COMPLETED, it wrote FILE NOTE FOUND. All the other programs that I transfered also looks like this, but this one I can't tranfer it, I don't understand.

 

%

O2102

#32=#25

#33=#26

G65P2001 X#1 Y#2 Z#3

G65P2003 A#1 B#2 C#3 D#4 E#5 F#3 K1. Q#21 R#17 S#18 T#19

#1=#[#17]

#2=#[#18]

IF[ABS[#23]LT0.0001]GOTO01

DPRNT[RAW*POINT*#1[44]***#2[44]***#3[44]]

N01

IF[ABS[#15]LT0.0001]GOTO02

#27=#14+#16

G65P2001 Z#27

G65P2001 X#6 Y#7

G65P2001 Z#3

GOTO03

N02

G65P2001 X#6 Y#7 Z#3

N03

G65P2003 A#6 B#7 C#3 D#8 E#9 F#3 K1. Q#21 R#17 S#18 T#19

#6=#[#17]

#7=#[#18]

IF[ABS[#23]LT0.0001]GOTO04

DPRNT[RAW*POINT*#6[44]***#7[44]***#3[44]]

N04

IF[ABS[#15]LT0.0001]GOTO05

#27=#14+#16

G65P2001 Z#27

G65P2001 X#10 Y#11

G65P2001 Z#3

GOTO06

N05

G65P2001 X#10 Y#11 Z#3

N06

G65P2003 A#10 B#11 C#3 D#12 E#13 F#3 K1. Q#21 R#17 S#18 T#19

#10=#[#17]

#11=#[#18]

IF[ABS[#23]LT0.0001]GOTO07

DPRNT[RAW*POINT*#10[44]***#11[44]***#3[44]]

N07

IF[ABS[#15]LT0.0001]GOTO08

#27=#14+#16

G65P2001 Z#27

N08

IF[ABS[#24]LT0.0001]GOTO999

G65P2016 A#1 B#2 C#6 D#7 E#10 F#11 X#17 Y#18 Z#20

#25=#[#17]

#26=#[#18]

#27=#14

IF[ABS[#32]LT0.0001]GOTO09

#28=#1-#25

#29=#2-#26

GOTO10

N09

#28=#25-#1

#29=#26-#2

N10

#30=0

#31=SQRT[[#28*#28]+[#29*#29]]

#28=#28/#31

#29=#29/#31

#[#17]=#1

#[#18]=#2

#[#19]=#3

G65P2013 A#28 B#29 C0 I#17 J#18 K#19

#1=#[#17]

#2=#[#18]

#3=#[#19]

IF[ABS[#32]LT0.0001]GOTO11

#28=#6-#25

#29=#7-#26

GOTO12

N11

#28=#25-#6

#29=#26-#7

N12

#31=SQRT[[#28*#28]+[#29*#29]]

#28=#28/#31

#29=#29/#31

#[#17]=#6

#[#18]=#7

G65P2013 A#28 B#29 C0 I#17 J#18 K#19

#6=#[#17]

#7=#[#18]

IF[ABS[#32]LT0.0001]GOTO13

#28=#10-#25

#29=#11-#26

GOTO14

N13

#28=#25-#10

#29=#26-#11

N14

#31=SQRT[[#28*#28]+[#29*#29]]

#28=#28/#31

#29=#29/#31

#[#17]=#10

#[#18]=#11

G65P2013 A#28 B#29 C0 I#17 J#18 K#19

#10=#[#17]

#11=#[#18]

G65P2016 A#1 B#2 C#6 D#7 E#10 F#11 X#17 Y#18 Z#20

IF[ABS[#33]GT0.0001]GOTO15

#[#20]=#[#20]*2.

N15

#[#19]=#14

N999

M99

%

[Mickey@acceltool]

cnc memory full?

[Mickey@acceltool]

incorrect file extension?

[Mickey@acceltool]

just my 2 cents!

[Watcher]

Can you save a program from the control to the USB stick? If so compare the extensions and the header.... Jm2c

[Guest]

I/O channel needs to be set first and foremost. Next, if you're trying to get all of your programs out (O8000's and O9000's)' you'll need to change parameter 3202 (NE9 and NE8 can't recall the bits off the top of my head) to 0's, then change to edit mode, then press the System button, soft arrow key over to ALL-I/O, then press PROG, and it'll copy all your programs to your USB Stick.

 

Hth