Because this machine has never been set up for 4th axis work like the and I’ve had great success modifying the post to get what I need . I havent had any luck using the MD all my rotations are the opposite direction or just wrong

I am setting up a post for a HMC and I want to break the rotations of B axis to limit it to 360 deg. I’m cutting a pocket substituting x axis but its winding 360 deg around. the post says to modify " pmotion_su" but I don’t know what to change. I’m not using the MD to set variables. thanks in advance B -440 should read B- 80.104 and so on G20 G0 G17 G40 G49 G80 G90 ( ROUGHT POCKETS +.01 ) T1 M6 G0 G90 G54 X0. Y3.1417 B-440.104 S1500 M3 G43 H1 Z4.885 Z3.085 G1 Z2.8382 F1. G42 D1 Y1.205 F5. G93 B-435.825 F23.59 G94 Y3.2185 F5. G93 Y3.1976 B-436.607 F113.61 rev_brkflag : 1 #Revolution break flag. 0 = No break, 1 = Break every 90 or 360 degrees (see pmotion_su) pmotion_su #Motion Setup (Set brklinestype & linarc) brklinestype$ = zero linarc$ = zero if rot_on_x, [ if cuttype = one, #Axis Substitution [ linarc$ = one #Linearize all arcs if rev_brkflag, #Break rotation flag (set in pcoutrev) [ brklinestype$ = 11 #Break all lines, use brklineslen$ for segment length #brklineslen$ = pi$ * rotdia$ #Break every 360 degrees brklineslen$ = pi$ * rotdia$ / four #Break every 90 degrees rev_brkflag = zero #Reset flag ] ] if cuttype = two, #Polar [ brklinestype$ = rotary_axis$ + three linarc$ = one ] ]

I am machining slots around a 16" dia, im using curve with chain and all is great except the slots are not 360 deg around the part so when it transitions to the start point the tool follows it all the way through and cuts through the part the file is to large I know its the kinomatcis but I don't know how to adjust them thanks

like wise whats the ftp psass

Mill man it is the add on for mx7 and bsemp I read that pdf but it dosent say anything about enabling it in mx7 and yes im just waiting for the code to be sent to me. we use cimquest new England formerly s4a

Hello, I just got productivity + for a 2 week trial. First how do I enable it I down loaded it and installed it but in MX7 it says its not enabled? Second anyone have any good resources for learning it thanks

OPTIONS SAVE AS

I have only noticed this with x7.. when I save a STL model from the verify and then bring it in to verify next op the STL model is very grainy?? is this normal for x7 now thanks

Thanks im still getting a wrong g code error I think its a parameters thing from the builder

Im trying to use high speed machining but I keep getting a improper g code for the g05.1q1 is there a parameter that is not turned on or off im also running it off a sim card with m198 witch I have done before on previouse tools centers using the hsm thanks N1 G20 N2 G00 G17 G40 G80 G90 N3 G91 G28 Z0. (X7 OKK HM-600 MACHINE 58) (MACHINE GROUP-2) N4 M08 N5 T4 M06 (0.5 FLAT ENDMILL) N6 (MAX - Z.1) N7 (MIN - Z-1.338) N8 G00 G17 G90 G54 N9 X-6.8298 Y22.1439 S12000 M03 N10 G49 N11 G05.1 Q1 N12 G43 H4 Z.1 N13 Z0. N14 G01 Z-1.338 F180. ------- ------- ------- N12873 X-5.1867 Y1.7592 R.1125 N12874 X-5.1483 Y1.7522 R.1125 F180. N12875 G03 X-4.0654 Y1.3747 R28.5085 N12876 G02 X-4.031 Y1.3564 R.1125 N12877 X-4.0253 Y1.3516 R.1125 F500. N12878 G01 X-3.9728 Y1.3046 N12879 G00 Z.1 N12880 G05.1 Q0 N12881 M09 N12882 G91 G28 M19 Z0. N12883 G28 X0. Y0. N12884 G90 N12885 M30 %

Not at all hope it works out for you

got it thanks

Ok that makes scense do I assume I need to remove the undercuts before then. here is a copy of the file BOOLEAN.MCX-7

Im trying to make a fixture for a thin chassis and I keep getting the error non manifold, I understand what that is but how do I fix it, thanks

yes i did read this when it came out it seems its nothing really new its just knowin ghow to get it done