Poxino
-
Posts
19 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Store
eMastercam Wiki
Blogs
Gallery
Events
Posts posted by Poxino
-
-
G00 g54 g90 x69.509 y60.453 s1936 m03
g43 h1 z12.
G64
z-17.02
g03 x69.603 y60.357 z-17.036 i1.02 j0.916 f1211.
X69.707 y60.272 z-17.051 i0.925 j1.012
x69.819 y60.196 z-17.064 i0.821 j1.098
x69.937 y60.132 z-17.077 i0.71 j1.173
x70.061 y60.08 z-17.087 i0.591 j1.237
x70.19 y60.041 z-17.094 i0.467 j1.289
x70.322 y60.014 z-17.099 i0.338 j1.329
x70.455 y60. Z-17.1 i0.206 j1.355
g01 x70.455
g02 x70.994 y59.951 i-0.382 j-7.147 f1478.63
g03 x72.066 y59.886 i2.257 j28.335 f1384.22
x76.921 y59.827 i4.564 j177.067 f1388.67
g01 x83.377 f1426.88
g02 x83.39 y59.827 i0. J-0.128 f1097.84
g01 x84.181 y59.747
g02 x84.202 y59.743 i-0.013 j-0.127 f938.47
g01 x84.995 y59.527 f1240.16
g02 x87.236 y58.2 i-1.804 j-5.603 f1783.
X87.917 y57.452 i-5.133 j-5.356
x89.165 y55.005 i-6.308 j-4.757
g01 x89.167 y54.995
x89.357 y54.245
x89.359 y54.237
x89.499 y53.486
g02 x89.727 y51.206 i-23.354 j-3.489 f1559.25
x89.802 y48.93 i-96.922 j-4.342 f1305.14
x89.827 y45.138 i-574.442 j-5.733 f1240.16
g01 y-53.475
g02 x89.827 y-53.49 i-0.128 j0. F1038.7
g01 x89.741 y-54.232 f1240.16
g02 x89.737 y-54.25 i-0.127 j0.015 f1783.
G01 x89.54 y-54.995
x89.537 y-55.005
x89.406 y-55.38
g02 x89.402 y-55.391 i-0.121 j0.042
x88.862 y-56.41 i-6.459 j2.767
x87.953 y-57.482 i-5.501 j3.744
x85.687 y-58.909 i-5.024 j5.465
g01 x85.351 y-59.037
x85.005 y-59.155
g02 x84.995 y-59.158 i-0.041 j0.121
g01 x84.202 y-59.36
x84.194 y-59.362
x83.399 y-59.512
g02 x80.186 y-59.771 i-3.773 j26.765 f1510.32
x76.176 y-59.823 i-4.479 j191.654 f1240.16
g01 x75.374 y-59.825
x74.572 y-59.827
x72.192
g03 x72.139 y-59.83 i0. J-0.511 f1037.57
g01 x71.379 y-59.91
g03 x71.349 y-59.914 i0.053 j-0.508
g02 x70.561 y-60. I-1.169 j7.061 f1783.
G03 x69.674 y-60.391 z-17.02 i0.073 j-1.369 f1682.19
x69.581 y-60.504 i0.48 j-0.489 f25000.
G01 x69.552 y-60.548
x69.503 y-60.672
x69.473 y-60.809
x69.465 y-60.942
x69.483 y-61.057
x69.531 y-61.138
x69.615 y-61.168
x70.467 y-61.166
x80.949 y-60.921
x81.269 y-60.909
g03 x81.589 y-60.881 i-0.385 j6.173
g01 x83.782 y-60.629
x84.245 y-60.559
g03 x85.146 y-60.313 i-1.167 j6.073
g01 x86.243 y-59.924
x86.701 y-59.741
g03 x88.346 y-58.661 i-2.527 j5.645
g01 x88.894 y-58.16
x89.314 y-57.739
g03 x90.71 y-55.144 i-4.591 j4.144
g01 x90.814 y-54.74
x90.924 y-54.229
g03 x91.012 y-53.189 i-6.097 j1.038
g01 x90.97 y49.63
x90.966 y49.852
g03 x90.954 y50.074 i-6.18 j-0.225
g01 x90.735 y53.09
x90.663 y53.686
g03 x90.533 y54.272 i-6.096 j-1.042
g01 x90.159 y55.643
x89.992 y56.163
g03 x89.227 y57.607 i-5.799 j-2.148
g01 x88.835 y58.155
x88.468 y58.621
g03 x86.609 y60.073 i-4.667 j-4.059
g01 x86.16 y60.302
x85.641 y60.537
g03 x83.417 y60.976 i-2.289 j-5.745
g01 x70.191 y61.184
x70.065 y61.185
x69.983 y61.156
x69.936 y61.077
x69.92 y60.965
x69.93 y60.833
x69.96 y60.697
x70.007 y60.572
x70.039 y60.518
g03 x70.11 y60.419 i0.59 j0.348
x70.976 y59.953 z-17.1 i1.039 j0.895 f1211.
G01 x70.976 y59.953
g02 x71.276 y59.909 i-0.903 j-7.1 f1783.
G03 x71.286 y59.907 i0.086 j0.504 f1182.65
g01 x71.715 y59.843 f827.93
g03 x71.747 y59.839 i0.075 j0.505
g01 x72.484 y59.777
g03 x75.533 y59.678 i3.348 j55.804 f1141.53
x81.61 y59.661 i5.046 j716.979 f1240.16
g01 x81.615 f1783.
X82.366 y59.63
g02 x82.378 y59.629 i-0.005 j-0.128
g01 x83.129 y59.529
g02 x84.459 y59.175 i-1.142 j-6.976
x84.472 y59.17 i-0.042 j-0.12 f1288.59
g01 x85.145 y58.844 f1240.16
g02 x85.157 y58.837 i-0.056 j-0.115 f1038.7
g01 x85.762 y58.462 f1240.16
g02 x85.773 y58.454 i-0.067 j-0.109 f1288.51
g01 x86.332 y58.022 f1783.
G02 x86.341 y58.013 i-0.078 j-0.101 -
I use solidcam which has a similar feature, but again it does not seem to be any different
-
Hello guys,
Just an update, after many weeks I managed to get my 2mb memory upgrade done on my machine.
It still does not make much difference in terms of motions, machine still struggles a lot where there are many small movement to be processed (0.01mm segments) , slows down about 80% of the programmed feed rate or more.....
Any suggestions, or I just need to forget about it as the machine and control are too old to do what I want to do?
-
Hello all,
I am new to this forum, but so far I have had a lot of help from the forum members.
I am now trying to figure out an easy and safe way to set tool offsets and z0 on my control.
I do have a master tool setter , and an haimer 3d taster to set work offsets.
The way I am doing it is
Reference machine first,then
for the tool offsets , just measure them with imput c at 0 on top of mastertool.
I measured 3d taster on top of mastertool too.
For the zo work offset I just touch part (or wherever the z datum is) until the 3d taster is at its 0 point, then go to work offsets , highlight z datum, type the 3d taster lengh , then measure.
Now all work well until I need to change a tool and re-set its lenght, or simply for instance add another tool in my program(then set a new tool lenght), and lenght come out wrong.
Additional notes: I must use g49 before toolchanges, and at the end of program I am using g28.
Thanks in advance for your answers!
-
I will upgrade my machine memory this weekend , as I had issues on getting an sram card(for parameters back up) that actually works on my control, then I will be running programs from machine memory only.
But at this stage, I hope to be wrong, but I believe that toolpaths I want to run are "too modern" for the actual machine capabalities , unless there are other parameters which need to be tweaked, the max speed I am running these toolpaths is around 100ipm 2500mm/min.
-
In certain areas of the toolpath there .01mm movements, in fact is where machine slows down most , I have run just a fraction of that program for testing, from memory, and is slightly better, but it still slows down a lot.
-
I am studying hard the parameters manual of the Fanuc 16mb, but certain parameters I am not too sure what they mean!
Thanks for your help!I will wait!:)
-
Hi,
Maybe I did not word the sentence properly, I meant is slowing down up 10% of the programmed feed rate , just to give you am example programmed feed rate 2500(100ipm)mm/min and actual feed rate 250 (10ipm)mm/min.
This was happening also before changing the parameters above.
But, as said machine is not banging anymore, which is already something.
I am not sure if there are other parameters I could have a look at?
Thanks again
-
Hello Sticky,
As said before, I am installing the 2mb memory upgrade this weekend,so I will be running programs from memory. Have you got a suggestion for changing other parameters?
From other emastercam posts there seem to be another parameter called allowable velocity difference in velocity determination considering the velocity difference at corners.
As said before , now machine is not banging anymore , which is a good result , but on those small movements machine still slows down a lot up to 10% of the programmed feed rate.
I think tool path I am running as micron tolerance , certain movements differ between them for just .008mm.
Again, any suggestion?
Many thanks to all in advance!
-
I will as soon I have the chance!
I am only interested on "hsm" only for roughing purposes , I still don't understand why the difference in motion between a simple normal tool path and this trochoidal style machining ,, could it be the small movements?It slows down up to 30% of the programmed feed rate , but now without banging so is already better than before.
Any other tweaks suggestions I could do?
I am not sure if parameter 1762 I posted previously could be any good to be changed?
Anyway , I am happier than before , thanks again!!!!!!!
I will keep the forum updated!
- 1
-
Hello there ,
I tried only today to switch those parameters and machine is moving much smoother!! :):):):)
I am so happy! you can still see the machine slowing down , but motion is smoother , and you don't hear any banging :):)
Any other paramter I can change or any other suggestions?
I am upgrading my machine memory next to week , with a 2mb module.
Regards
-
Hi ,
I haven't had the chance to tweak parameters yet.
I could be wrong , but I think I found the equivalent of param 1769 on 16 MB.... looks like param 1762 ( I could be wrong).
So would be 1762 , 1768 ,1771.
Param 1762 , is all set to 0 at the moment.
Attached the screen shoots with param description.
My 2mb pcmcia card should be coming today I got it in order to back up my parameters , but I am not sure if control can drip feed from memory card.
I spent few hours yesterday on the books , and it seems that G05.1q1/q0 does not exist in this Fanuc ... only g08 , g05 p10000
-
Hi ,
I checked the parameters 1768 and 1771 and they are set @ 20 and 80 , can I change them with any number , or is there a criteria to change them? I .e . multiplies of 2 /4 ..... etc...
Sorry for the silly questions , but I actually never done this before.
I couldn't actually find parameter 1769 , it seems like it does not exist , but it seems the most import one too.
-
Newbeeee , I checked those parameters on my manual but I could only find paramters before interpolation , and during cutting feed in look ahead mode...
I will take a picture of the ones you mentioned , as I am not sure what values I should change them to.
What parameter number could be the one for jerky motion?
Can this tuning damage servos?
Thanks for the help
-
Hi
Thanks again for all the replies, I was not expecting so many!:)
I know that for hsm , drip feeding might not be the best solution, however I am feeding machine at 100ipm max , so I believe is not super fast... to me it seems the control process the code fast enough, but machine struggles on small movements/ changes of direction/ spline execution.
I think that as I also tried tp run a small part of program with those small g1 movements , splines etc, but I couldn't notice a difference.
Once my pcmcia card arrives I will try to drip feed from card.
-
I think Fanuc data server is an option... but I will search on this forum...
Thanks
-
Hello guys, thanks for your replies!
I really appreciate!
Baud rate is the max available 19200.
I might have another look at those parameters , but not sure if the apply to g08.
-
Hello there,
I am new here , and I have no much experience with HSM , that's why I am asking here, hope I will get some help!
I have been trying hard to get high speed machining right on my Robodrill T10b with fanuc 16mb, I do have G08 function, but machine is still very jerky even @40 ipm, I am running an high speed toolpath.
I am drip feeding program.
Cad cam software is outputting Gcode mostly in g2/g3 output with some small movements between g2/g3 , when machine moves in g2 and g3 and on long g1 movements it's very smooth!
I am not totally sure, but I believe it's not a problem with CAM software...
G64 is active too.
Are there any parameters that can be tuned to improve the motion?
Anybody knows if g5.1 q1 can be an option that can be bought on this Fanuc 16mb? Does it need a software or hardware upgrade , it does not mention this very well on the manual I have.
Thank you guys for the time in advance ,
Regards
fanuc 16mb high speed machining
in Machining, Tools, Cutting & Probing
Posted
How do I do that?