Remove machine and group names

[Doug Funny]

Greetings all,

I want to remove the group and machine name from the top of my program, see below. I've been up and down the post and cannot find where the heck it posts it out. I'm using the mpmaster post for 2023.

 

Thanks,

Doug

%
O2041 (GG2041M10)
(CUSTOMER NAME= ARCH)
(PART NUMBER= 250449XX)
(PART NAME= EDM FIXTURE)
(PROGRAMMER= D PIERCE)
(OPERATION NUMBER=)
(DATE= 2/9/23)
(JOB= 28348)
(DMG-MORI CMX1100)    <------------------- I want to remove this line
(MACHINE GROUP-1)       <------------------- and this line
(T5   - 1/2 FLAT ENDMILL     - H5   - D5   - D0.5000")
(T17  - 3/8 SPOTDRILL        - H17  - D17  - D0.3750")
(T18  - NO. 7 DRILL          - H18  - D18  - D0.2010")
(T19  - 1/4-20 CUT TAP       - H19  - D19  - D0.2500")
(OVERALL MAX - Z.25)
(OVERALL MIN - Z-1.4417)
G00 G17 G20 G40 G49 G80 G90
G53 Z0.
M01

[Leon82]

Put a # in the header area on the line where those are output. It should be able to see what's on each line

[H.tom]

8 hours ago, Doug Funny said:

Greetings all,

I want to remove the group and machine name from the top of my program, see below. I've been up and down the post and cannot find where the heck it posts it out. I'm using the mpmaster post for 2023.

 

Thanks,

Doug

%
O2041 (GG2041M10)
(CUSTOMER NAME= ARCH)
(PART NUMBER= 250449XX)
(PART NAME= EDM FIXTURE)
(PROGRAMMER= D PIERCE)
(OPERATION NUMBER=)
(DATE= 2/9/23)
(JOB= 28348)
(DMG-MORI CMX1100)    <------------------- I want to remove this line
(MACHINE GROUP-1)       <------------------- and this line
(T5   - 1/2 FLAT ENDMILL     - H5   - D5   - D0.5000")
(T17  - 3/8 SPOTDRILL        - H17  - D17  - D0.3750")
(T18  - NO. 7 DRILL          - H18  - D18  - D0.2010")
(T19  - 1/4-20 CUT TAP       - H19  - D19  - D0.2500")
(OVERALL MAX - Z.25)
(OVERALL MIN - Z-1.4417)
G00 G17 G20 G40 G49 G80 G90
G53 Z0.
M01

opening   your Control Definition file,  Choose "NC Output":

 

Output operation comments to NC

Choose whether to include operation-specific comments in the NC program. These are created in the Toolpath parameters tab for each operation. This setting is a default which can be overridden in the Machine Group Properties.

Output machine name to NC

Choose whether to include the machine name as a comment in the NC program. The name comes from the machine definition. This setting is a default which can be overridden in the Machine Group Properties.

Output group name to NC

Choose whether to include the name of the machine group in the NC program, as displayed in the Toolpaths Manager.

Output group comments to NC

Choose whether to include machine group-specific comments in the NC program. These are created in the Files tab of the Machine Group Properties.

[Doug Funny]

On 2/15/2023 at 8:18 PM, H.tom said:

opening   your Control Definition file,  Choose "NC Output":

 

Output operation comments to NC

Choose whether to include operation-specific comments in the NC program. These are created in the Toolpath parameters tab for each operation. This setting is a default which can be overridden in the Machine Group Properties.

Output machine name to NC

Choose whether to include the machine name as a comment in the NC program. The name comes from the machine definition. This setting is a default which can be overridden in the Machine Group Properties.

Output group name to NC

Choose whether to include the name of the machine group in the NC program, as displayed in the Toolpaths Manager.

Output group comments to NC

Choose whether to include machine group-specific comments in the NC program. These are created in the Files tab of the Machine Group Properties.

 

 

That didn't make a difference. It's still posting those lines out

[Doug Funny]

I found it finally! it was in the pcomment2 section...