Manual Enrty Output Position

[kenfromlodi]

I would like my manual entry to come out in between my tool changes. It currently will come out after the first line of the next tool.

 

What designation calls up the Manual entry comment?

 

how do I need to place it so it will be in the right spot?

 

This is how it currently posts

 

code:

---

M01

(************)

N29G00G40G80G90G98

(SPOT HOLE)

G06T29(1/4-90 SPOT DRILL)

(*)

G53Z0

G54B75.

(*)

X-7.4292Y2.82S2500M03T109

Z12.1M08

G81G61G98Z8.88R9.2F10.

G80M09

M80

M01

(************)

N109G00G40G80G90G98

 

M0(HAND LOAD TOOL)--THIS IS WHERE IT COMES OUT NOW

 

(DRILL .3125" INTERSECTING HOLE)

G06T109(5/16 DRILL EXT 6.3)

(*)

G53Z0

G54B75.

(*)

X-7.4292Y2.82S1500M03T115

Z12.1M08

G83G98Z3.4R9.2Q.1F8.

G80M09

M80

M01

---

This is how I would like it.

 

code:

---

M01

(************)

N29G00G40G80G90G98

(SPOT HOLE)

G06T29(1/4-90 SPOT DRILL)

(*)

G53Z0

G54B75.

(*)

X-7.4292Y2.82S2500M03T109

Z12.1M08

G81G61G98Z8.88R9.2F10.

G80M09

M80

M01

 

M0(HAND LOAD TOOL)--THIS IS WHERE I WOULD LIKE IT

 

(************)

N109G00G40G80G90G98

(DRILL .3125" INTERSECTING HOLE)

G06T109(5/16 DRILL EXT 6.3)

(*)

G53Z0

G54B75.

(*)

X-7.4292Y2.82S1500M03T115

Z12.1M08

G83G98Z3.4R9.2Q.1F8.

G80M09

M80

M01

---

any help will be great.

 

I am using X4 . post was put thru the up dater from X2

[EazyE]

Mine seems to post fine...

I am using the Mpmaster from the post link at top of page.

 

N3270 G1 X-3.5736 Y-2.96 Z.0006 F6.4

N3280 X-3.5906 Y-2.945 Z.0067

N3290 X-3.6054 Y-2.932 Z.0195

N3300 X-3.6165 Y-2.9223 Z.0377

N3310 X-3.6228 Y-2.9167 Z.0596

N3320 X-3.624 Y-2.9156 Z.0752

N3330 Z.1688

N3340 G0 Z2.1688

N3350 M5

N3360 G91 G28 Z0.

N3370 M01

( MANUAL ENTRY LINE )

N3380 T1 M6

N3390 G0 G90 G110 X-3.5859 Y-2.9236 S1382 M3

N3400 G43 H1 Z2.5734

N3410 Z.5984

N3420 G1 Z.5734 F6.4

N3430 X-3.5886 Y-2.9208 Z.5496

N3440 X-3.5965 Y-2.9129 Z.5283

N3450 X-3.6088 Y-2.9007 Z.5116

[EazyE]

I am not a post guy by far. But after searching (manual) I gound this section of my post that from what I can see is the call section..

 

# Tool Comment / Manual Entry Section

# --------------------------------------------------------------------------

ptoolcomment #Comment for tool

tnote = t$, toffnote = tloffno$, tlngnote = tlngno$

if tool_info = 1 | tool_info = 3,

sopen_prn, pstrtool, sdelimiter, *tnote, sdelimiter, *toffnote, sdelimiter, *tlngnote, sdelimiter, *tldia$, sclose_prn, e$

 

ptooltable #Tooltable output

sopen_prn, *t$, sdelimiter, pstrtool, sdelimiter, *tlngno$,

[if comp_type > 0 & comp_type < 4, sdelimiter, *tloffno$, sdelimiter, *scomp_type, sdelimiter, *tldia$],

[if xy_stock <> 0 | z_stock <> 0, sdelimiter, *xy_stock, sdelimiter, *z_stock],

sclose_prn, e$

 

pstrtool #Comment for tool

if strtool$ <> sblank,

[

strtool$ = ucase(strtool$)

*strtool$

]

 

pcomment$ #Comment from manual entry (must call pcomment2)

pcomment2 #Required if doing boolean 'if' logic testing!

 

pcomment2 #Output Comment from manual entry

scomm$ = ucase (scomm$)

if gcode$ = 1005, sopen_prn, scomm$, sclose_prn, e$ #Manual entry - as comment

if gcode$ = 1006, scomm$, e$ #Manual entry - as code

if gcode$ = 1007, sopen_prn, scomm$, sclose_prn #Manual entry - as comment with move NO e$

if gcode$ = 1026, scomm$ #Manual entry - as code with move NO e$

if gcode$ = 1008, sopen_prn, scomm$, sclose_prn, e$ #Operation comment

if gcode$ = 1051, sopen_prn, scomm$, sclose_prn, e$ #Machine name

if gcode$ = 1052, sopen_prn, scomm$, sclose_prn, e$ #Group comment

if gcode$ = 1053, sopen_prn, scomm$, sclose_prn, e$ #Group name

if gcode$ = 1054, sopen_prn, scomm$, sclose_prn, e$ #File Descriptor

 

# --------------------------------------------------------------------------

# Start of File and Toolchange Setup

[kenfromlodi]

Thanks guys,

I usually do pretty good on stuff like this and have not had to make any edits to my post for quite a few months now. its funny how much you forget in a few months.

[kenfromlodi]

you know my MPMaster works great also and even after comparing the it against mine I am still unsure.