Probe Set Y and X location

[kennebec]

Good Morning Forum

 

Fanuc 18I on Kiwa Horizontal mill

the 8001 and 8002 probe cycles in the following code should set the G58 Y and X based on the J and C locations in the cycle however these cycles simply set Y and X 0 at the probed location, do you Probe useres see what I am doing incorrectly?

 

N20T120M106

G0G90G58B180.M62(B180)

M98P8999

(PROBE HOLE AND SET G58 Z OFFSET/INDICATOR)

X0.Y-.35(SET G58 Y )

G43Z8.H120

Z.1

G65P8002C.1J-.155T.07U-.07V0.W5.Y.135Z-.11 (J is the Y Location)

G0G90Z2.

#2605=[#2605+#104]

G58X.34Y.0(SET G58 X )

Z.1

G65P8001C.1I.139T.05U-.05V0.W5.X.118Z-.11 ( I is the X location)

G0G90Z2.

#2505=[#2505+#104]

G58X0.Y0.(SET G58 Z )

Z.1

G65P8003C.1K0T.03U-.03V0.W5.Z-.1

G0G90Z8.

 

 

Thanks Forum

[kennebec]

Sorry I ddid not explain 2 lines of math I added to force the adjustment I want please se it below

 

Thanks again everyone

 

N20T120M106

G0G90G58B180.M62(B180)

M98P8999

(PROBE HOLE AND SET G58 Z OFFSET/INDICATOR)

X0.Y-.35(SET G58 Y )

G43Z8.H120

Z.1

G65P8002C.1J-.155T.07U-.07V0.W5.Y.135Z-.11 (J is the Y Location)

G0G90Z2.

#2605=[#2605+#104]---------------------------This math was added to adjust for the X axis not setting to the Y location

G58X.34Y.0(SET G58 X )

Z.1

G65P8001C.1I.139T.05U-.05V0.W5.X.118Z-.11 ( I is the X location)

G0G90Z2.

#2505=[#2505+#104]---------------------------This math was added to adjust for the X axis not setting to the X location

G58X0.Y0.(SET G58 Z )

Z.1

G65P8003C.1K0T.03U-.03V0.W5.Z-.1

G0G90Z8.

[kennebec]

Thanks Forum, Im allset, the cycles work as they are and the math is needed if you want to set probed location to anything other than Zero...

[Guest CNC Apps Guy 1]

Do you have Renishaw EasySet? You can set whatever you want, whereever you want it.

 

 

 

 

[Craig-B]

Shouldn’t J be (J0.) instead of (J-.155), that how it would be on Renishaw, not sure on your machine.

[kennebec]

Do you have Renishaw EasySet? You can set whatever you want, whereever you want it.

 

No Nothing just Caron Engineering Book, Copy Paste Edit to suit, any info you can share about where to look into purchasing EasySet?

 

 

Thanks Again...

[kennebec]

Shouldn’t J be (J0.) instead of (J-.155), that how it would be on Renishaw, not sure on your machine.

 

As it Turns out you are right it should be Zero however the book reads "Position to Set" this to me implies I can say what I want that location to be, but that is not the Case, Except in the 8003 (Z set cycle) You can set the Z to the K dimension.

Thanks for the help this forum is reaaly a great place...

[GoetzInd]

You might want to think about buying the inspection plus macros for your machine if you don't already have them. Would save you a ton of time.

 

Mike

[Guest CNC Apps Guy 1]

I believe I saw some Renishaw stuff in the Unspecified Uploads folder on the FTP not too long ago. Check it out if you get a chance.

[kennebec]

I believe I saw some Renishaw stuff in the Unspecified Uploads folder on the FTP not too long ago. Check it out if you get a chance.

 

 

Thanks will do...