Register now to participate in the forums, access the download area, buy Mastercam training materials, post processors and more. This message will be removed once you have signed in.
Use your display name or email address to sign in:
Hi All:
I program for several different machine types. I am trying to fine tune the posts so the same MC9 file will out to all machines types.
1: For my Fadal post I want remove 4th axes code at the begining of the program.
Example:
%
N1 O0002(MP-P0002)
N2 G20
N3 G0G17G40G49G80G90H0E0Z0
N6 T1M6
N7 M61 (remove)
N8 A-0. (remove)
N9 M60 (remove)
N10 G0G90S300M3E1X0.Y0.
It slowes down the machine while the brake goes on and off.
2: For my ProtoTrak post I want to remove the line numbers and remove M8 & M9 even if the MC9 file has it turned on.
Thanks for the help....
Gary
Thanks All:
The post is working with one problem. After a tool change the first D outputs OK. G41 D41 X0 y0. But the rest of the G41s have no D. G41 X0 Y0.
Sample code:
T19M6
G0G90G54X-10.0708Y-3.154A0.S2139M3
G43H19Z2.M8
Z.1
G1Z-.27F6.42
G41D59X-9.9626Y-3.2165(has 40 added to D. OK)
G3X-9.5876Y-3.R.25
X-10.6956R.554
G1G40X-9.6621Y-2.8202
G0Z2.
X-.0533Y-3.154
Z.1
G1Z-.27
G41X.055Y-3.2165 (Does not put D for each G41
G3X.43Y-3.R.25
Here’s what I changed
# Toolchange / NC output Variable Formats
# --------------------------------------------------------------------------
fmt T 4 t #Tool Number
fmt T 4 first_tool #First Tool Used
fmt T 4 next_tool #Next Tool Used
fmt D 4 tloffno #Diameter Offset Number
fmt D 4 tloffno40 #Diameter Offset Number + 40 #added this line
fmt H 4 tlngno #Length Offset Number
pccdia #Cutter Compensation
#Force Dxx#
tloffno40 = tloffno + 40
if prv_cc_pos <> cc_pos & cc_pos,
prv_tloffno = c9k
sccomp
if cc_pos, tloffno40 #Changed from tloffno # Changed this line
Is there something I need to change?
Thanks again
Gary
Hi all:
I hope I can describe what I need so you can under stand it. I have to program the same parts to run on three different machines. Fadal, Mazak, Matsuura.
What I am want to do is make one MC9 file with the tool dia. offset and tool length offset set the same as the tool no. (under Job setup, Tool Offset Registers, Add checked, length and diameter set to 0). Then, when I run the post for Fadal and Mazak, it will out put T1 - D1 - H1.
Can I change the mpfan.pst so that I can use the same MC9 file (with tool dia. offset set same as tool number) but have the post output T1 - D41 - H1 ?
Basically take the tool dia. offset and add 40 to in the post..
I hope I haven’t confused everyone..
Thank
Gary
Hi All:
If I start a new mc9 file and save it as "new port.mc9" and post my nc file. Then I see my spelling mistake. It should be "new part.mc9". I can rename my mc9 file and resave it. But when I repost the nc file it still comes out as new port.nc not the corrected name Where in mc9 do I change it so it will post the corrected file name..
Tkanks
Gary
Hi All:
Is it possible to insert a saftey/stop move before or after a operation on the Operation Manager?
(saftey/stop move)
G0G80G90M5M9
Z0G53
X0Y0Z0E0H0
M0
This is for Fadal.
Like this....
1. pocket
2.contour
3.(insert g code)
4 contour
I hope you understand...
Thanks
Gary
I have been running Mastercam v7 on a old Pentium 233 till it refused to boot up for the last time. Now I’m running Mastercam v9 mill 1 on a Dell 100D Smartstep. That's a Calderon processor. Could that be the problem?
They(purchasing)said they would get my a better video card if I will guarantee it will solve the problem...
I am using V9. When I am programming I go to Contour and start pick some entities I use to see a green arrow at the start of the entities and a red arrow at the end of the entities or at a branch. Now when I pick entities the arrows blink on to the screen for about a millisecond and disappear. How can I fix this so the arrows stay on the screen.
I am using Mastercam V9 Mill level 1 and Windows 98 2nd Edition.
I went to:
MY COMPUTER
CONTROL PANEL
SYSTEM PROPERTYS
DEVICE MANAGER
DISPLAY ADPTER
it says
INTEL®82810 GRAPHICS CONTROLER
Thanks
GARY
I'm not sure what your asking.
I went to:
MY COMPUTER
CONTROL PANEL
SYSTEM PROPERTYS
DEVICE MANAGER
DISPLAY ADPTER
it says
INTEL®82810 GRAPHICS CONTROLER
Is that what you are looking for?
Gary
eMastercam - your online source for all things Mastercam.
Together, we are the strongest Mastercam community on the web with over 56,000 members, and our online store offers a wide selection of training materials for all applications and skill levels.