I added two lines, This gives me an advance, but the advance of the draft code: pread_g70 #Read G70 recall buffer feed = sav_feed if lathecc = four foundcc = zero size2 = rbuf (two, zero) wc2 = one while wc2 <= size2 & foundcc = zero, [ fcc_subid = rbuf (two, wc2) if fcc_subid = sub_op_id$, [ gcodecc = zero ng70s = fcc_ng70s ng70e = fcc_ng70e pbld, n$, *scclgcode, *ng70s, *ng70e, pffr, e$ foundcc = one ] ] As I understand it, code: if lathecc = four determines the draft or the finish thanks to the variable? code: lathecc : 0 #Flag for canned turning cycle type #1 = G71/G72 rough cycle #2 = G73 pattern repeating cycle #3 = G74/G75 groove cycle #4 = Finish pass for types 1 and 2 #Neg.=rough and finish, Pos.=rough only Someone to help me please

Welcome back, To complete my cycle of problem and outline on my Haas finiton, because I lack the speed advantage on my cycle, G70. code: G70 P20 Q40 F.... I am amused to add the orders * feed, feed and pffr, on the line code: pbld, n$, *scclgcode, *ng70s, *ng70e, e$ But the PP generates me an advance of F10000 code: pfcc_call$ #G70 recall output postblock if cc_stop_fcc = zero, [ pread_g70 if foundcc = zero, result = mprint(sfccerror) ] no_nc_out$ = zero cc_stop_fcc = zero pread_g70 #Read G70 recall buffer foundcc = zero size2 = rbuf (two, zero) wc2 = one while wc2 <= size2 & foundcc = zero, [ fcc_subid = rbuf (two, wc2) if fcc_subid = sub_op_id$, [ gcodecc = zero ng70s = fcc_ng70s ng70e = fcc_ng70e pbld, n$, *scclgcode, *ng70s, *ng70e, ..?.., e$ foundcc = one ] ] pwrite_g70 #Write G70 recall buffer fcc_subid = sub_op_id$ fcc_ng70s = ng70s fcc_ng70e = ng70e fcc_subid = wbuf (two, rc2) Thank you in advance

Thank you very much, If you do not live that far, I t'aurais asked to drink an aperitif.

Hello, Even me, this time I have another little problem. When I do a course outline for the training and a course outline for machining outside addresses recalls Block P. .. Q. .. are the same for both cycle. code: G72 P20 Q40 U0. W.2 D2. F.25 N20 G0 Z0. S130 G1 X-1.6 N40 Z5. G0 X95.117 ( EBAUCHE EXTERIEUR ) G0 X95.117 Z2. X94. G71 P20 Q40 U.5 W.1 D3. F.3 N20 G0 X50. S130 G1 Z-30. N40 X94. G0 Z2. I suppose that the change should be somewhere here. code: prcc_call_end$ #Rough canned cycle end # Restore cc_1013 to the value it held prior to the rough # 1/17/03 # groove canned cycle. cc_1013 was changed in ptoolend. # 1/17/03 if tool_op$ = 208 | tool_op$ = 62, cc_1013$ = sav_cc_1013 # 1/17/03 if tool_op$ <> 208, [ omitseq$ = sav_omitsq #Close the ext file result = fclose (sbufname3$) #Open the ext file as a buffer #Use the size to determine the start and end sequence subout$ = sav_subout size3 = rbuf(three, zero) if omitseq$ = one, [ ng70s = n$ ng70e = n$ + seqinc$ ] else, [ if old_new_sw = zero, ng70s = n$ + seqinc$ else, ng70s = n$ + (seqinc$ * two) ng70e = ng70s + (seqinc$ * (size3 - one)) ] pwrite_g70 ] Thank you in advance.

It's good, its running Thank you very much

Thank you, That is what I thought. Only problem, pp my generates a code with the address for the depth of cut U quote: N780 G71 P800 Q820 U.4 W.2 U2. While the address must be D I tried to change here, but its not working code: # Canned cycle output format (do not change order, used by buffer 2) # -------------------------------------------------------------------------- fmt U 2 depthcc

Hello, I am looking for the command to the depth of cut for roughing cycle G71. quote: N780 G71 P800 Q820 U.4 W.2 F.4 D? N790 G0 X50. S90 N800 G1 Z-30. N810 X90. code: pg71new #Output G71-G72 canned cycle routines, new style, first if gcodecc = 1, result = nwadrs (stru, depthcc) else, result = nwadrs (strw, depthcc) #pbld, n$, *scclgcode, *depthcc, *clearcc, e$ #modif 1.02 supression g71 r pbld, n$, *scclgcode, *ng70s, *ng70e, *xstckcc, *zstckcc, pffr, strd ? e$ Thank

Apparently, I take a course in simple drilling or breaking, the generated code remains "CUSTOMIZABLE DRILL CYCLE" X0 Z-30

Hello Colin Gilchrist, In fact it is a pp that I recovered. I thought that the Eob had to be edited by CIMCO, I will try to transfer the program to see if it is automatically generated during the transfer. I'll let you know tomorrow. For against, I hangs on G83 drilling cycle, the PP generation "CUSTOMIZABLE DRILL CYCLE" I found the script to change, but I do not know how coment. ldrill$ #Canned drill cycle, lathe #Use this postblock to customize lathe drilling cycles 0 - 7 pdrlcommonb "CUSTOMIZABLE DRILL CYCLE ", pfxout, pfyout, pfzout, e$ pcom_movea

The EOB will come in by itself at the machine. Why do you want it to post with it ?? Is that why you have a% at the beginning and at the end of the program? The program released by CIMCO has no EOB: rolleyes:

Hello, I can not find how to add an EOB ( at the end of each line in the pp. What should I change Thank you in advance for your help

Thank JParis@CNC Programming Solutions®

Please its march The pilots are developed with dell, I saw her on touslesdrivers.com, the site did not want to let me download the update, leaving me a message saying that I had to pass through the support dell.

Hello, I have to disable the acceleration in configuring the software. I Vista Premium, and apparently the drivers for my graphics card are specific to Dell

Hello, I just installed the X2 MR2 SP1, on my new laptop. Dell XPS M1330 Intel Centrino Duo 4 Giga RAM Nvidia GForce 8300 GS My problem is that I am obliged to disable hardware acceleration, if its does not follow, my screen is blank. Is there any special configuration to be done in the panel Nvidia? Thank you