I downloaded the latest driver for my Quadro FX540 I set a restore point before installing. I'm glad i did! Mastercam wouldn't even completely load using that driver. I'd just get the Mastercam's send an "Error Report" dialogue so I'm back to where I was. I'm not going to worry to much about this anymore, my new box is being ordered next week: Core 2 Quad Q6600 ASUS S775 P5E3 Core 2 board 4 Gig ram (realising the limitations running 32bit op) Quadro FX 1700 XP pro Any comments on this config much appreciated before I place the order

Not even the developers??

This is the error get when opening files.

Hi Bruce, I'm glad to see i'm not the only one with the white screen issue. I tried to take a snapshot of the screen in this state and I couldn't get an image. I'm not glad to see you have this issue with a Quadro FX1500 card though I was hoping this problem would disappear with a card like that. This most definately is a MC graphics issue.

I never had an opportunity to see if it helped the crashing issue because Mastercam was nearly unusable with that setting changed. For me the crashing happens erratically. I can open the file normally on one occasion or it will crash on another. As mentioned above i'm using a NVIDIA Quattro FX540. I realise this card is a entry level card and plan to go to a midrange FX1700 with a new machine we are having built. As always cost is an issue

quote: Does this happen if you disable hardware acceleration in Mastercam's Settings->Configuration Screen? I tried that at it runs terrible, dynamic rotation is erratic and slow so have changed it back. I often get a white screen when I am opening files. This is usually files that have toolpaths on them. Also when i am writing a toolpath and i change to another task the Mastercam screen will be white when I return to it, and slowly the toolpath generation will reappear. This has always been a problem in version X right from the outset. Does anyone else have these graphics issues with mastercam? As always comments appreciated

I often get an exception error and Mastercam crashes when opening largeish files. If I open the files unshaded I have no problems. Happened on MR2 and also happens with MR2 SP1? System is Pentium D 3.2ghz, 2gig Ram, NIVIDA Quattro FX 540 video. I'm getting a new box in a few weeks and after browsing the Benchmark thread its going to be Core 2 Quad Q6600, 4gig Ram Quattro FX 1700 video. Any comments much appreciated

quote: This has been logged as bug number cnc00031226. Thank you. --- Christopher Bell Quality Control Engineer CNC Software

quote: This is a bug in MR2. I have the same problem and sent it in during Beta testing only to find it wasnt fixed in the release.Thanks Ed, so looks like we'll have to wait until another patch is released and maybe it will be addressed then??

quote: Ok I've changed the setting to Prompt - Always and use MCX file name instead of previous operation name. Now I just have to substitute the MCX name with the file name I want each time I make a new operation which is basically what I was doing before anyway.After working some more this morning I'm not finding this method ideal at all. I still want to be able to have a prompt for the first operation and then be prompted for a file name on subsequent operations as well ie SP1. Any suggestions?

Ok I've changed the setting to Prompt - Always and use MCX file name instead of previous operation name. Now I just have to substitute the MCX name with the file name I want each time I make a new operation which is basically what I was doing before anyway.

Hi guys, Haven't been on here for some time but of course the opportunity always arises when there is an upgrade I've just upgraded from X2 SP1 to MR2 (I tried MR1 but had graphics problems so went back to SP1) I did a fresh install of MR2 and everything has been working fine so far One thing I have found though is that even though the configuration settings for the Toolpath Manager are exactly the same as my SP1 setup it won't ask me for a NC file name on the first operation. It defaults to the MCX file name. But on subsequent ops it asks me for the name. Anyone finding this and/or is there a fix. Any suggestions help much appreciated

My X2 is definately faster that X1 in all respects

The toolpath isn't the problem because I only want the files for a Design seat. The Design seat hasn't got a maintenance contract so we may have to look into that or buy an upgrade to X2 for that seat.Anyway thank you for all the input my question has been answered Cheers

Hi Thad A Mastercam box with CD, User Guide about 1" thick, Transition guide, Installation guide, mouse pad and reference card.