This is with live tooling on the face of the part.

This is what I've figured out. % O0000 (3_CYL_SLEEVE) (DATE=DD-MM-YY - 06-04-16 TIME=HH:MM - 12:43) (MCX FILE - C:\\_3_CYL_SLEEVE_BACKSIDE 3-31-2016.MCX-9) (NC FILE - C:\\3_CYL_SLEEVE.NC) (MATERIAL - ALUMINUM INCH - 6061) G20 (TOOL - 7 OFFSET - 7) ( 7/16-14 TAPRH) T0707 M154 M8 G97 P210 M133 G98 G17 G00 G54 X8. Z1. C0. X1.5 G95 Z-.65 F15. ( 210RPM * .0714"Pitch = 15.0IPM Feed rate ) C90. C180. C270. G00 G80 X8. Z1. C0. M9 M155 M135 G53 Y0. G53 X0. G53 Z0. M30 %

Isn't 14/1= .071426" * 218" = 15.57" Then G95 inches /rev I guess 15.57" per rev would cram the tap right to -.650" instantly. I will look at my parameters in the morning and see if I ca find my mistake. Thanks

I just got off the phone with HAAS and the M49 should be a G49. MasterCam post error. Now I'm getting exceeds max federate. T0707 M154 G49 M8 G97 P218 M133 G99 G17 G00 G54 X8. Z1. C0. X1.5 ************************** This line ? G95 Z-.65 F15.57 C90. C180. C270. G00 G80 X8. Z1. C0. M9 M155 M135 G53 Y0. G53 X0. G53 Z0. M30 %

Hello All, I recently purchased a new HAAS ST20SSY lathe with live tooling. I'm getting an error 329 m code not defined. if anyone has had this same issue I would like to hear your fix. I've included the code MasterCam X9 is outputting. Thanks, % O0000 (3_CYL_SLEEVE) (DATE=DD-MM-YY - 06-04-16 TIME=HH:MM - 12:43) (MCX FILE - C:\\3_CYL_SLEEVE_BACKSIDE 3-31-2016.MCX-9) (NC FILE - C:\\ROTEC_3_CYL_SLEEVE.NC) (MATERIAL - ALUMINUM INCH - 6061) G20 (TOOL - 7 OFFSET - 7) ( 7/16-14 TAPRH) T0707 M154 M49 M8 G97 P218 M133 G99 G17 G00 G54 X8. Z1. C0. X1.5 G95 Z-.65 F15.57 C90. C180. C270. G00 G80 X8. Z1. C0. M9 M155 M135 G53 Y0. G53 X0. G53 Z0. M30 %

Hello all, I have a Coleague that want to export an inventer solid that has GD&T added to it. Then have mastercam recognize the GD&T when imported. Thinking he would not have to create a print for the job. Anyone seen something like this work? Thanks,

what do you want to know. Cutting granite with diamond tools?

Thanks all Bernie's post sent me in the right direction. Rick

Hi I created the geometry for the disc in the top cplane then i created the rectangular box in the front cplane.But i am cutting from the top. Thanks for all the help. I'll try this stuff later rick

Hi everyone. I'm new to MC so I hope this comes out right. I have created a round disc 1 inch thick in MC. I'm trying to mill a flat on one edge. The disc is 5" in diameter. The flat has to be .200" In from the outer diameter. The way I was trying to do this was to create a rectangle in the front construction plane the move it out to the diameter so I can extrude .200" into the side. The problem is that when I go to contour the flat the verify shows it cutting around the rectangle. Can anyone help?? Rick