10 minutes ago, crazy^millman said:

 

 

Both of you support this statement that this loud mouth will repeat.

 

The all-mighty big programmers Go xxxxing read what the original question was! The all-mighty big xxxxing programmers, you all are so ignorant and do not even realize that you all do not have any understanding that even close to the operator and still mucking him! Shame on all of you! The common offset is handy in many cases, and all the machine builders keep that option. Yes, it has consequences, and you have to be careful, but every single touch on the CNC machines has that potential too. 

THE OPERATOR IS SO RIGHT AND THE BIG MOUTH @crazy^millman YOU ARE THE BIG MOUTH AS USUAL

Can I add that factor into setup sheet for cycle time ?

Is there any way to manipulate the setup sheet cycle time?

Peck drill cycle time is reasonable in the machine simulation but it is significantly off in the setup sheet.

Is there any solution?

9 hours ago, BehindYou said:

Can you send me your post so I can take a look
Email: [email protected]

Ivan,

I sent it to you.

i find some comment manipulation topic in this forum that you can break the comment with using special character

maybe this can help

https://www.emastercam.com/forums/topic/79766-comment-manipulation/page/2/

thanks again for your help

1 hour ago, BehindYou said:

In this case you have encrypted post.
.PSB file which you can't open.
You should contact your reseller to do changes which you want.  

when i check with mp post for encrypted section it is basically come to end with this section

  if gcode_comm = 1006 & scomm_out <> snull,  n$, pspc,            *scomm_out, e$ 

when i made a change in this section it is changing the post output for the codes
but I couldn't make it to place it at the different line as lack of my knowledge 

Thank you for your respond @BehindYou

When i debug it this is my result from

NC output: 

 |62||109|M5 M9 G4P.5 M51 S1222M3 G4P.5|pscomm_fmt_out[PST:362, 72]|plin$  +  pncoutput  +  pscomm_all_out  +  pcomment_scan_out  +  pscomm_fmt_out  +  pspc

Post:

pscomm_fmt_out  #set format and output of each Mastercam generated comment
      scomm_out = ucase(scomm_out)

      spaces$ = 0
      if gcode_comm >= 1051 & sof & scomm_out <> snull,     scomm_str, *scomm_out, scomm_end, e$
      if gcode_comm = 1005 & scomm_out <> snull,  n$, pspc, scomm_str, *scomm_out, scomm_end, e$, pfel
      if gcode_comm = 1006 & scomm_out <> snull,  n$, pspc,            *scomm_out, e$ 
      if gcode_comm = 1007 & scomm_out <> snull,  scomm_str, *scomm_out, scomm_end
      if gcode_comm = 1026 & scomm_out <> snull,             *scomm_out
      if gcode_comm = 1008 & scomm_out <> snull,  n$, pspc, scomm_str, *scomm_out, scomm_end, e$
      spaces$ = sav_spc

NC output: 
|63|T.MIN|109|-> M5 M9 G4P.5 M51 S1222M3 G4P.5|-> plin$[PST:4380,  7]|plin$  +  pncoutput  +  pscomm_all_out  +  pcomment_scan_out  +  pscomm_fmt_out  +  pspc

Post:

ENCRYPTED POST SECTION

colored blue lines are the responding lines for the codes

but i can not see individual code in the post that i can manipulate like in your example 

what should I do?

Thanks again...
 

In Advanced Drill toolpath at the code entry section i would like to enter more than one code.

But in the post it generate all codes are in the same line. 

Can I get each code at the different line

Example:

ENTRY CODE: M5 M9 S1000M3 G4P1. 

G1 Z-.5 F10.

M5

M9

S1000M3

G4P1.

G1 Z-1.2 F5.