toolanddieprogrammer
-
Posts
29 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Store
eMastercam Wiki
Blogs
Gallery
Events
Everything posted by toolanddieprogrammer
-
engraving curved surface
toolanddieprogrammer replied to toolanddieprogrammer's topic in Industrial Forum
Thank you all VERY much for all the help. The 2D toolpath-pocket and Toolpaths surface Rough with enable cavity do not seem to be compatible when pocket standard is selected in source operations. Maybe the HLE version has a problem with this I get multiple errors . -
engraving curved surface
toolanddieprogrammer replied to toolanddieprogrammer's topic in Industrial Forum
TUTORIAL #7 WIREFRAME MILL LEVEL 3 F.zipTx 4 response I get failed to get motion to project please regen operation error reading from surface machining temp file
-
Hi everyone I am looking to find how to machine the M into the part. This is the last lesson for mill level 3 so I am looking forward to wrapping it up. Thanks to everyone who has posted for me.
-
Ruled Lofted Problem
toolanddieprogrammer replied to toolanddieprogrammer's topic in Industrial Forum
Hello I created the geometry a little different than the tutorial and then it worked thanks for the help -
Ruled Lofted Problem
toolanddieprogrammer replied to toolanddieprogrammer's topic in Industrial Forum
TUTORIAL #7 WIREFRAME MILL LEVEL 3 C.zip I did one of them by accident I redid the create curve on one edge and retried and it worked sync chains is new to me right now I wish the tutorial book explained this more they must know this problem -
Ruled Lofted Problem
toolanddieprogrammer replied to toolanddieprogrammer's topic in Industrial Forum
Hi. actually I do not, I tried all the sync options in ruled lofted but no luck I added a screen shot I have only been learning Mastercam for 2 months I still need to learn more
-
Hello all thanks for all the help with all of my questions I've had. I can't seem to get the ruled lofted to work properly on these chains. I was wondering if someone could tell me what is wrong I try to start them in the same spot and chain them in the same direction but no luck. Thanks all.
-
I must say a lot of Tutorial # 6 is messed up, it is like nobody poof read it at all
-
Hello all
-
Hello all. I am having a problem with this fillet. This is mill level 3 Tutorial # 5. In the book there is a note NOTE: The fillet surfaces are generated correctly but the draft surface is not trimmed. To fix this you should enable EXTEND SURFACES in the FILLET-SURFACES OPTIONS as shown. This does not fix the problem does anyone have a fix for this.
-
thank you all I did get it I had to reclick on second surfaces again to reaim the arrows or it would say no fillets selected thanks again everybody
-
here is a zipped file mill level 3 tutorial # 1 Review Exercise C.zip
-
Yes the trim box is checked
-
I have tried this many times it doesn't work but thanks for your help
-
I added pic of how fillet turns out
-
this is a mill level 3 exercise to draft surface, create curve on edge, flat boundary surface and fillet surface I was able to add 3 fillets but the top one wont work
-
Hello there I am having a problem adding a fillet to my part I need some help
-
this is an exercise to import a solidworks file, xform translate 3d from the mill level 1 training tutorial series
-
This attached file is exercise #5 mill level . I can not use wireframe Tutorial #5 Exercise.SLDPRT
-
hello all. I have a question about solids in the mill level 1 exercise #5 they machine it in wireframe in the chaining box but I am unable to do it unless I use solids why is this. I have not been able to with any other solids either. If anybody knows about this it would be a big help. tx
-
Hello all. I have a problem with the mill level 1 tutorial # 5. I have the file opened but when the chaining box opens I can not chain any of the lines in wireform but can if the solid is selected. I have done other solids and its the same I am wondering if this is normal or is a setting wrong. If anybody has an answer it would be appreciated.ty
-
that makes sense I well do that tvm
-
I can create it. it just wont machine it
-
Hello I am just learning Mastercam. I want to do thread but o.d. turning doesn't turn din undercut any ideas thanks for any replies.
-
Hello I am very new to Mastercam and feeling dumb.I xed the operations manager window now I cant get it back could someone let me know how to bring it back tx
