LATHE INSERT INFO

[mirek1017]

Hello all ,I am using  generic 2axis fanuc  postprocesor for my lathe machine 

When I am post my code I dont have any information about my insert  like shape or angle and corner rad .Haw I can change the post for get all this information in my codes 

thank you for any help 

 

[BehindYou]

What you need is in 2000's parameters

from there you can get info about the tools

tcr$ is varable which will give you tool tip radius 

[mike49107]

Quote

On 8/2/2023 at 10:31 AM, BehindYou said:

What you need is in 2000's parameters

from there you can get info about the tools

tcr$ is varable which will give you tool tip radius 

 

I know that this is an old thread, but could you please provide more information on how to accomplish this?  I have asked my reseller to add this to our post and was told that it is not possible. 
thank you. 

[BehindYou]

OFC it's possible 

Here is my output which I use

(----------------------------------------------------------)
(T27  | KENNAMETAL_D20_3D    | D27  | INSERT - R0.00 )
(#1. | Lathe_Drill | )
(     |  VC = S2627 mm/min       |     )
(     |  MAX RPM = S2627 RPM     |     )
(     |  Feedrate = 0.15 mm/rev |     )
(==========================================================)
(==========================================================)
(T1   | WALTER_CNMG          | D1   | INSERT - R0.80  )
(#2. | Facing | )
(         |   VC = S265 mm/min       |         )
(         |   MAX RPM = S2685 RPM     |         )
(         |   Feedrate = 0.23 mm/rev |         )
(==========================================================)
(==========================================================)
(T41  | ISCAR_DCGT           | D41  | INSERT - R0.10 )
(#4. | Rough | )
(     |  VC = S185 mm/min       |     )
(     |  MAX RPM = S2874 RPM     |     )
(     |  Feedrate = 0.20 mm/rev |     )
(==========================================================)
(==========================================================)
(T74  | 3D LATHE TOOL-2      | D74  | INSERT - R0.20 )
(#5. | Plunge rough; also, chained grooves | )
(     |  VC = S125 mm/min       |     )
(     |  MAX RPM = S1850 RPM     |     )
(     |  Feedrate = 0.10 mm/rev |     )
(==========================================================)
(==========================================================)
(T75  | WALTER_ID_GROOVE_D20.00_2.00 | D75  | INSERT - R0.20 )
(#6. | Plunge rough; also, chained grooves | )
(     |  VC = S100 mm/min       |     )
(     |  MAX RPM = S1850 RPM     |     )
(     |  Feedrate = 0.10 mm/rev |     )
(==========================================================)
(==========================================================)
(T5   | WALTER_VNMG          | D5   | INSERT - R0.40  )
(#8. | Finish | )
(         |   VC = S185 mm/min       |         )
(         |   MAX RPM = S2874 RPM     |         )
(         |   Feedrate = 0.14 mm/rev |         )
(==========================================================)

[BehindYou]

Check your PM, 
Code is there,
Make sure that you did backup before changing your code.

Kind regards

Ivan

[mike49107]

Thank you. I’ll try to test it soon if I can get some time. 

[mirek1017]

23 hours ago, mike49107 said:

Thank you. I’ll try to test it soon if I can get some time. 

Hello ,its  work ?

[zhaochuanfang]

y时

[BehindYou]

English please