HAAS MPMASTER chip break, change i to q

[PACDIE]

O0000 How do I change the "i" to a "q" so the machine knows what to do?

O0000 (LU5285 1ST OP)
(MPMASTER-CH)
(1ST OPP HAAS)
(PROGRAM   - LU5285 1ST OP.NC)
(DATE      - JAN-16-2024)
(TIME      - 7:29 AM)
(T3   - #51 SCREW DRILL      - D0.0670")
G00 G17 G20 G40 G80 G90
G91 G28 Z0.
M08
T3 M06 (#51 SCREW DRILL)
(MAX - Z6.)
(MIN - Z5.3002)
G00 G17 G90 G54 X-3.6742 Y-2.2593 S12000 M03
G43 H3 Z6.
G94
G98 G73 Z5.3002 R5.5002 I.05 F20.
X-4.6742
G80
M09
M05
G91 G28 Z0.
G28 Y0.
G90
M06
M30
%

[JParis]

You shoot off an email to your reseller and they fix it up for you in about 30 seconds...

[Jake L]

probably the format on peck1$

Don't know for sure without seeing you're post, proceed with caution

[BehindYou]

On 1/16/2024 at 4:32 PM, PACDIE said:

O0000 How do I change the "i" to a "q" so the machine knows what to do?

O0000 (LU5285 1ST OP)
(MPMASTER-CH)
(1ST OPP HAAS)
(PROGRAM   - LU5285 1ST OP.NC)
(DATE      - JAN-16-2024)
(TIME      - 7:29 AM)
(T3   - #51 SCREW DRILL      - D0.0670")
G00 G17 G20 G40 G80 G90
G91 G28 Z0.
M08
T3 M06 (#51 SCREW DRILL)
(MAX - Z6.)
(MIN - Z5.3002)
G00 G17 G90 G54 X-3.6742 Y-2.2593 S12000 M03
G43 H3 Z6.
G94
G98 G73 Z5.3002 R5.5002 I.05 F20.
X-4.6742
G80
M09
M05
G91 G28 Z0.
G28 Y0.
G90
M06
M30
%

Greetings,
 In your post find  this section. If you are able to open it check the section below (If your post file ends with .psb you can't edit your post and you should contact your reseller)
# Drill output
# --------------------------------------------------------------------------
fmt  "R" 2  refht_a     #Reference height
fmt  "R" 2  refht_i     #Reference height
fmt  "X" 2  initht_x    #Initial height, mapped X
fmt     2   initht_y    #Initial height, mapped Y
fmt  "Z" 2  initht_z    #Initial height, mapped Z
fmt  "X" 2  refht_x     #Reference height, mapped X
fmt     2   refht_y     #Reference height, mapped Y
fmt  "Z" 2  refht_z     #Reference height, mapped Z
fmt  "X" 2  depth_x     #Depth, mapped X
fmt     2   depth_y     #Depth, mapped Y
fmt  "Z" 2  depth_z     #Depth, mapped Z
fmt  "Q" 2  peck1$      #First peck increment (positive)
fmt     2   peck2$      #Second or last peck (positive)
fmt  "R" 2  peckclr$    #Safety distance
fmt     2   retr$       #Retract height
fmt  "Q" 2  shftdrl$    #Fine bore tool shift
# --------------------------------------------------------------------------

second step:
check if output is fine by you, if you want output without dot make sure to check Format statements section in your post and set how you want your output.

If you have more questions, feel free to ask.

Kind regards.

Ivan