Lathe X6 home position control and y axis?

[Darin]

Hello,

 

I have a MPLmaster post I am trying to make it post a G30 when I use home position user defined in X6 before and after tool change .. Also I need it not to post any Y axis code or a G54 ... How can I do this?

 

 

Here is how it posts now

 

G20

(TOOL - 1 OFFSET - 1)

(OD ROUGH RIGHT - 80 DEG. INSERT - CNMG-432)

(MIYANO)

(HEX_CAPSCREW_1.00-8UNCX3.00)

(ROUGHS FACE)

G0 G54 X10. Y0. Z10. <------------------------------------------ Need this line to post only G30 X** Z** and no G54 or Y-------------------------------------------->

N1 T0101

G18 G99

M24

G97 S312 M03

G0 X2.45 Z.5

G50 S3500

G96 S200

Z.055

G1 X-.0625 F.01

G0 Z.155

X2.45

Z.01

G1 X-.0625

G0 Z.11

X2.45

Z0.

G1 X-.0625

G0 Z.1

(ROUGHS O.D.)

X2.0506

Z.21

G1 Z.11

Z-3.6812

X2.192 Z-3.6105

G0 Z.21

X1.8512

G1 Z.11

Z-2.99

X1.8575

G3 X2.02 Z-3.0713 R.0812

G1 Z-3.9813

X2.1614 Z-3.9105

G0 Z.21

X1.6518

G1 Z.11

Z-2.99

X1.8575

G3 X1.8712 Z-2.9903 R.0812

G1 X2.0126 Z-2.9196

G0 Z.21

X1.4524

G1 Z.11

Z-2.99

X1.6718

X1.8133 Z-2.9193

G0 Z.21

X1.2531

G1 Z.11

Z-2.99

X1.4724

X1.6139 Z-2.9193

G0 Z.21

X1.0537

G1 Z.11

Z-2.99

X1.2731

X1.4145 Z-2.9193

G0 Z.21

X.8543

G1 Z.11

Z-.0021

X.9863 Z-.0681

G3 X1.0105 Z-.0973 R.0412

G1 Z-2.7543

G3 X1.0305 Z-2.7813 R.0412

G1 Z-2.99

X1.0737

X1.2151 Z-2.9193

(FINISHES O.D.)

G50 S3600

G0 Z.1

X0.

G1 Z0.

X.7959

G3 X.8401 Z-.0092 R.0313

G1 X.9722 Z-.0752

G3 X.9905 Z-.0973 R.0312

G1 Z-2.7583

G3 X1.0105 Z-2.7813 R.0313

G1 Z-3.

X1.8575

G3 X2. Z-3.0713 R.0713

G1 Z-3.95

X2.1414 Z-3.8793

G0 X5.

G97 S76

G0 X10. Y0. Z10. <------------------------------------------------------------------- Need this to be G30 X** Z** only -------------------------------------------------->

M01

(TOOL - 7 OFFSET - 7)

(OD THREAD LEFT INSERT - NTC-3L10E)

(MIYANO)

(HEX_CAPSCREW_1.00-8UNCX3.00)

(TURNS 1-8 THREADS)

G0 G54 X10. Y0. Z10.

N7 T0707

G18 G99

G97 S200 M03

G0 X1.19 Z.2281

G76 P010060 Q10 R0.

G76 X.8512 Z-2.75 P694 Q214 R0. F.125

G0 X10. Y0. Z10.

M05

M30

%

[cjhajek]

Try running DeBug. this will help find the origin of the post output. Small changes in the post followed by sample output is best. Also try to watch for unwanted output in other areas.

[crazy^millman]

Darin, you need a good understanding of posts and if you are not sure where in the post to do this I would strongly suggest you contact your dealer and see if they can assist you.

 

HTH