HEDENHAIN i TNC 530

[mirek1017]

hello All ,this same one try programing  cycl  deff 19  on hedenhain control with M130  .I can not find any sample on web ,My new post  put in the codes M130 and the control show me error .When I delete this code machine do not move my working plane after rotate B C axis 

 

this is sample my codes 

4 ; POST         - ALZMETALL_CS_TNC
5 ; MATERIAL     - ALUMINUM INCH - 2024
6 ; PROGRAM      - 3+2 TEST.H
7 ; DATE         - AUG-16-2018
8 ; TIME         - 12:46 PM
9 ; 
10 BLK FORM 0.1 Z X-2.185 Y-1.425 Z-4
11 BLK FORM 0.2 X+2.185 Y+1.425 Z+0
12 ; TOOL 8     - 3/4 FLAT ENDMILL     - H8     - D8     - DIA +0.75"
13 M127
14 M129
15 CYCL DEF 7.0 DATUM SHIFT
16 CYCL DEF 7.1 X+0
17 CYCL DEF 7.2 Y+0
18 CYCL DEF 7.3 Z+0
19 CYCL DEF 19.0 WORKING PLANE
20 CYCL DEF 19.1
21 L Z-0.5 R0 FMAX M91
22 L X+1 Y+1 R0 FMAX M91
23 L B+Q121 C+Q122 FMAX
24 ; B90 C180 CONTOUR
25 * - TOOL 8     - 3/4 FLAT ENDMILL     - H8     - D8     - DIA +0.75"
26 TOOL CALL 8 Z S1700
27 M08
28 CYCL DEF 7.0 DATUM SHIFT
29 CYCL DEF 7.1 X+0
30 CYCL DEF 7.2 Y+0
31 CYCL DEF 7.3 Z+0
32 CYCL DEF 19.0 WORKING PLANE
33 CYCL DEF 19.1 A+90 B+0 C+270
34 L B+Q121 C+Q122 FMAX
35 L X+0.12 Y+1.8375 M130 FMAX ; TOP MAPPED APPROACH POINT
36 L X+1.8375 Y-0.12 FMAX M3
37 L Z+5.11 FMAX
38 L Z+2.11 FMAX
39 L X+1.35 RL F300.
40 L X-1.35
41 L X-1.8375 R0
42 L Z+5.11 FMAX
43 M09
44 M5
45 M140 MB MAX
46 L Z-0.5 R0 FMAX M91
47 CYCL DEF 19.0 WORKING PLANE
48 CYCL DEF 19.1
49 L B+0 C+0 R0 FMAX
50 M30
51 END PGM 3+2 TEST INCH

 

thanks for any  help 

[pullo]

I ran this program on  my machine :

1  I had to change Line 22 , ( the Y+1 to Y-1) so that  I could be inside my limits 

2. I had to correct the typo error in the M130 line  from M130 FMAX  to FMAX M130 

otherwise  the program ran  somewhat fine  ( in line 36 I added the Z 5.11 ): 

36 L X+1.8375 Y-0.12 Z5.11 FMAX M3

It wasn't like I was looking at a swan dance , but as far as the program , if you make the changes I made, should run OK 

So  the kinematics of the machine should be addressed if the machine does not behave properly.

Gracjan

 

 

[mirek1017]

Thanks pullo so much for your time and help .Yes ,I have kinematics problem .The funny thinks is ,when I call to the guy who sold as this machine ,he wants to change  pstprocesor and working with  out any cycles  from machine numbers !!!!this is so stupid ,you pay for mrcedes ,but you have to drive bike !!!!!I wait what owner wont to do with this .