-
Posts
177 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Store
eMastercam Wiki
Blogs
Gallery
Events
Posts posted by jimp
-
-
Phil I am using Ver 9.1 is Verpose available on that version?
Jim
-
sorry but what is "Verbose"
Jimp
-
The test is done with a bar that can output micron (0.0000393") changes in length. It is attached to both the spindle and a fixed point on the table. The machine is then put through a series of circular moves in the X/Y plane, and half-circle moves in the X/Z and Y/Z planes
Jimp
-
could not agree more give yourself a pat on the back.
Jimp
-
Quote
It's ironic how management views the "internet" as a time-waster. We should begin an open poll, counting all the time that emastercam has saved us all.
Agree with you 100% its helped me more times than I can remember. Just reading through the posts is an education
-
'when is x coming?'
How long is a piece of string?
JimP
-
Like Matthew I also used find PDF995 to publish .PDF documents. Now use CutePDF Writer another great share ware program.
Jimp
-
I fully agree with jack
-
-
If you go on Mastercam Site there 5 agents for China, and if it a Pirate copy you have, hope you will not be looking for any help in the future fron the Forum users. I can just hear James just now.
--------------------------------------------------------------------------------
Workvision Advanced Technology Corp
Web Page: http://www.mastercam.com.tw/
--------------------------------------------------------------------------------
CAMVision Shanghai Inc.
Web Page: http://www.mastercam.org.cn
EMail: [email protected]
--------------------------------------------------------------------------------
Kontech Development Ltd.
Web Page: http://www.kontech.com.hk/
EMail: [email protected]
--------------------------------------------------------------------------------
Techtown Pte. Ltd.
Web Page: http://www.techtown.com.sg/
--------------------------------------------------------------------------------
Workvision (Suzhou) Advanced Tech
Web Page: http://www.mastercam.net.cn
EMail: [email protected]
-
Yorkshire Precision in you guessed it Britain
A lot cheaper than you are paying even with transport costs.
Jimp
-
That woke me up jumped from 9.1 to 9.5 in three days, but then things are never as they seem.
Jimp Registered users since at least 1994
-
A wee bit far for me to travel from Scotland hope you all have a good time.
JimP
-
If it is a new machine can not see a problem. Programing EDM wire m/c can not be easier when using Mastercam.
-
No only the 9.1 Disc. Last time a installed I would have upgraded either from 9.0 or 8.1.
so that most likley isthe problem.
jimp
-
Roger Thanks Copied the file C:Program FilesMCUPartnersMastercamMCUGetOps.dll to the Chook directory why it was asking for this file I don't know but if it stops the error box appearing every time I was in the opp manager thats good enough for me.
Thanks again where would we be without this forum.
-
When I carry out and activity in the Operation Manager.
Thanks Jim
-
What is mcucetops.dll
Chook for
-
No I checked that Chook at startup set to None.
-
Agree with what you all say this Forum is the best.It has helped me solve problems in minutes rather than phone my mastercam agent and wait hours and some times days for their reply.
Jim
-
Hi all for some reason I am getting this error message on screen. I have a new hard drive and re installed Mastercam.
File not Found
c:mcam9chooksmcucetops.dll
Best regards Jim from Bonnie Scotland
-
Thanks for your help it worked a treat.
Jim
-
I using the Finish Toolpath to contour the bore from bottom then facing the part and wish to dwell on the face.
Have looked at the toolpath editor, how do I add dwell to toolpath?
Thanks again Jim
-
I am boring and facing a Quartz component and would like the tool to dwell at finish of facing opp is this posible.
Thanks in advance Jim
Feed change on chain - lathe
in Industrial Forum
Posted
Sorry Phil never noticed when I switch show cooridinates Verbose button comes active.
Thanks for your help and as I have said in the past you learn most by just reading through the posts.
Still the best wee forum in the World
Jimp