lowboy
-
Posts
50 -
Joined
-
Last visited
Never
Content Type
Profiles
Forums
Downloads
Store
eMastercam Wiki
Blogs
Gallery
Events
Everything posted by lowboy
-
Depends on the post,Some of the older Okuma posts did it automaticly.It used to be a switch inside the post.
-
If you are using the Lathe canned Finish, look on the second tab and there is a "approach point" Check the box and return to the screen and select an point to rapid to.Post should pick it up.
-
Should your Dealer be helping you on this?
-
Thank you sir
-
How can you delete all machine groups out of a file? Thanks
-
I was woundering if you apply a surface rough pocket toolpath and use solids selection and select all solids(the whole model even parts you do not intend to machine)will it increase computation time for the tool path,or will it just look at the features that are in the containment boundary? Thanks
-
Let me re-state that: Thank you ALL for your replys That was rude of me.
-
Thank you Roger Martin from CNC Software
-
Is there a way to show if the cutter is in G01,G00 etc. with the XYZ coordinates? I can see the coordinates at the lower left bottom of the sreen, but not the motion type. Thank you
-
I would like to have a shot at that one Can I get a copy of the file?
-
Thannk you very much, I missed that one
-
Hello,everybody, I am recieving an error when I post out my code,"Error-write nc operation information must be enabled in control definition-set & repost" What is it wanting me to do? Thanks in advance
-
Thanks for the reply's!!
-
I was woundering when machining an electrode using surface toolpaths,if you input a negative number in stock to leave, will this account for an accurate and uniform distance over all the selected surface?(over burn) Does it offset the surface evenly or do you need to do this your self by using the offset surface command? Thanks
-
Yes, I am going into G98, but it juts sits there. The control is so old we had to hard wire a jummper back in the late 70's to get it to work and I have lost my notes on this and was woundering if anybody here could help me out. Thanks
-
% O5000(JAW BORING PROGRAM) G50S1500M42 G0G96S200M8 T101M3 G0X.5Z.1(START DIA) G90X.6Z-1.F.009(THREE MOVEMENT COMMANDS HAPPEN HERE) X.7 X.8 X.9 G0Z.25 G30U0W0 M30 % (THIS CAN BE A SINGLE PASS ALSO)
-
G76 Bore shift question - Mori Seiki with Fanuc control
lowboy replied to a topic in Industrial Forum
A tool also shifts at the bottom by specifying addresses I an J. G98G76X1.Y1.Z-1.R.1I-.01J-.01F15. I and J are Modal I=X J=Y -
I am having a problem with an old CNC lathe with a Fanuc 6TB control.The problem is when I open the collet for the bar feeder, the control halts and will not execute the program any further.(the cycle will not execute with the chuck open) Is there an interlock via through the parameters, or is hard wiriing a by pass the only way? Thanks in advance
-
Any way I could get a look see? That's something we want to try.
-
In the solid model verify, is there a way to set the slider bar to quality as the default? Thank you
-
Thanks to all
-
In the config, under screen there is a item that says: "use free mode in dynamic spin" What does this do? Thanks
-
Which would be more Accurate to use in 3 axis machining, surfaces or solids? Which will give you the closes data to the real model?
-
Thanks! And Thank you for the answer.
-
If you change your toolbar state,close the software, re-launch the software, will the toolbar be where you las left them? Can I take a config .mtb file from a fresh install and replace it with another .mtb file. Should it over write the old one?