New Mpmaster

[DavidB]

I downloaded the new Mpmaster.

# Post Revision : 11.0.06347 (MC_FULL.MC_MINOR.YYDDD)

 

The rotations work much better Thanks Brett.

 

The tapping is differant though?

Here is an example of the new Mpmaster Tapping cycle.

 

code:

---

 T51 M06 (M12 TAP X 1.75 PITCH)

M97

M56 H1 D2

M11 (UNLOCK)

G00 G90 G54 B180. S100 M03

X-50. Y50.

M10 (LOCK)

G43 H1 Z105.

M08

G95

M135

G99 G84 Z90. R105. F1.75

X50. F175.

Y-50. F175.

X-50. F175.

G80

G94

Z400.

S20000 M03

M11 (UNLOCK)

B0.

M10 (LOCK)

X50. Y50.

Z105.

G95

M135

G99 G84 Z190. R105. F1.75

X-50. F35000.

Y-50. F35000.

X50. F35000.

G80

G94

Z400.

M09

M05

G91 G28 Z0.

M11 (UNLOCK)

G28 X0. Y0. B0.

M10 (LOCK)

G90

M99

%

---

The feed to move between holes is linked to the spindle speed and the pitch.

These moves should be in G0 mode?

I used the same tap at differant spindle speeds just to see what code I would I get.

 

Thanks

BTW: I added the M135 because my machine needs it other than that no other mods done.

 

[ 01-17-2007, 09:10 PM: Message edited by: DavidB ]

[monty]

Hi David,

Why do you need feed in lines after canned cycle. If you remove F from there it will automatically rapid to next point.

[DavidB]

quote:

---

Why do you need feed in lines after canned cycle.

---

I don't

 

The post is putting the F at position moves.

 

For some reason the New Mpmaster X2 post is putting a feed rate of spindle speed x pitch on each canned cycle position.

[monty]

It comes from pdrill_2 or ptap_2.

Look for *feed try changing to feed. It should work.

[DavidB]

G81 is OK

G84 gives feed @ position moves

code:

---

G99 G81 Z90. R105. F600.                                    pdrill$ pdrill$

X50. pdrill_2$ pdrill_2$

Y-50. pdrill_2$ pdrill_2$

X-50. pdrill_2$ pdrill_2$

G80 pcanceldc$ pcanceldc$

G99 G84 Z90. R105. F1.75 ptap$ p__133:2504

X50. F175.????? ptap_2$ pdrill_2$

Y-50. F175.????? ptap_2$ pdrill_2$

X-50. F175.????? ptap_2$ pdrill_2$

G80 pcanceldc$ pcanceldc$

---

code:

---

 ptap_2$          #Canned Tap Cycle

pdrill_2$

---

code:

---

 pdrill_2$        #Canned Drill Cycle, additional points

pdrlcommonb

pcan1, pbld, n$, pdrlxy, pzout, pcout, pindexdrl, prdrlout, dwell$,

feed, strcantext, e$

pcom_movea

---

[monty]

I tried same thing as I told you it worked for me.

 

Now I even tried removing feed from pdrill_2,It seems bit risky but It did not change any other output.

[DavidB]

quote:

---

Look for *feed try changing to feed. It should work.

---

From what section of the New Mpmaster X2 post?

 

Its not in ptap_2 or pdrill_2

 

Thanks

[DavidB]

Bump

[Guest]

David,

 

This is feedback I think would be better directed directly to Brett Thomas

[Tim Johnson]

Try this;

 

code:

---

ptap_2$          #Canned Tap Cycle

pdrlcommonb

pcan1, pbld, n$, pdrlxy, pzout, pcout, pindexdrl, prdrlout, dwell$,

strcantext, e$

pcom_movea

---

(copied pdrill_2 and removed feed)

[monty]

quote:

--------------------------------------------------------------------------------

 

From what section of the New Mpmaster X2 post?

--------------------------------------------------------------------------------

 

I removed feed from pdrill_2.

[DavidB]

Thanks all