Post Gurus needed, workofs$ & prv_workofs$ conflicting

[Tim Johnson]

I have made modifications to the "Lock on First WCS" so that it will lock on the current WCS. This works well with the exception of when I change the WCS on the same plane using the same tool. What happens is workofs$ and prv_workofs$ both are the next WCS. This is happening before ptlchg1002$

 

code:

---

N13830 G80          pcanceldc$ 7700.

pcanceldc$ pcan2 7700.

pcanceldc$ 7700.

ptoolend$ 7708.

pmiscreal$ 7708.

pmiscint$ 7710.

pmiscparam$ 7712.

psynclath$ 7720.

pscomm0$ 7730.

pscomm0$ 7730.

pparameter$ 7730. (removed a bunch of this line)

pparameter$ 7752.

pparameter$ 7752.

pparameter$ 7752.

pparameter$ 7752.

pparameter$ 7752.

pparameter$ 7752.

pparameter$ 7752.

pparameter$ 7752.

pparameter$ 7752.

pparameter$ 7752.

prot$ 7752.

prd1000$ 7752.

ptlchg00$ 7752.

1. mr8 test ptlchg1002$ p__77:1934 7752.

2 work test ptlchg1002$ p__77:1934 7752.

wcstype 2. wcstype test ptlchg1002$ p__77:1934 7752.

2 prv_workofs$ test ptlchg1002$ p__77:1934 7752.

ptlchg1002$ pspindle p__64:1772 7752.

---

code:

---

                    <<<<<<<<<<<< line 7700

999

2 0 75

1051

ENSHU JE60S

1053

ENSHU JE60S

1011

0. 0. 0. 0. 0. 0. 0. 1. 0. 0.

1012

0 0 0 0 0 0 0 0 0 0

1013

0 0.125 0. 0 3 -3.68998203 9.70000015 3.16999984 3 NONE <<<<<<<<<<<<<< line 7712

1014

-1. 0. 0. 0. 0. 1. 0. 1. 0.

1016

75 0 2 3 -3.68998203 9.70000015 3.16999984 0 2 0 2 0 0. -1 1 74 75 <<<<<<<<<<<< line 7716

1017

-1. 0. 0. 0. 0. 1. 0. 1. 0.

950

0 0 0 14234 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 <<<<<<<<<< line 7720

1025

0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

1027

1. 0. 0. 0. 1. 0. 0. 0. 1. 0. 0. 0.

1028

0 0 0. 0. 1. 0. 0. 1. 0 0 0 0

1029

0. 0. 0. 0. 0. 0. 0. 0. 0. 0 0

1020

0. 0. 0. 0. 0. 0. 0 0. 0. 0. 0. 0 13000

20010

OP2 CENTERING BACK

20011

---

The .nc file shows the .nci line going from 7712 to 7720. gcode 1013 (line 7712)and gcode 1016 (line 7716) are both showing my new WCS locations.

 

My question is does the post read line 7716 even if it's not being shown on the debug file? If it is could this be where my workofs$ and prv_workofs$ become the same? And if both questions are yes where would I fix it in the post?

[crazy^millman]

Could you do a sav_workofs_change nci code using that as a test and if it changes then force it to update?

 

gcode 1013 = sav_workofs_change

if sav_workofs_change <> gcode 1013, !gcode1013 in the ptlchg1002$ part of the post??

[Tim Johnson]

Ron,

 

It appears that I may be able to do a save in ptoolend$ and replace it in ptlchg1002$ but I was running out of time so I moved an op with a plane change between the two and moved on for now. I stuck a sticky note on my monitor and hopefully I can get back on it sometime next week.