simple 5ax cuts

[Scott Bond]

Hi all

I have a simple 5 ax cut, that looks correct

on the screen ,but the part is oval when it should be an elispe.

NEWTRACKB.MC9 (on Cadcam's FTP)

 

Could one of you guys look at my file, and tell

me if it would work . [or why not?]

 

So if it is ok on your screen, the problem will be that the A, and the, B are not set correct in the post. I have already contacted Cadcamn for post research.

 

[ 06-17-2002, 07:14 PM: Message edited by: Scott Bond ]

[gcode]

I put a file on the ftp labeled newtrackb-gcode.

Check it out.

Here is a sample of the posted code

Note: new file put on FTP at 5:22 PST

 

T1 M6

G0 G54 G90 X7.7507 Y0. C90. B-40. S2000 M3

G43 H1 Z17.8967

D21 Z13.8967

G1 G93 Z13.7967 F50.

X7.7535 Y.0958 Z13.7944 C86.17 B-40.002 F50.

X7.7608 Y.1812 Z13.7885 C82.538 B-40.004 F50.

X7.7711 Y.2576 Z13.7798 C79.066 F50.

X7.7839 Y.3269 Z13.769 C75.719 B-40.003 F50.

X7.799 Y.3908 Z13.7562 C72.458 B-40.001 F50.02

X7.818 Y.4587 Z13.7403 C69.089 B-40. F50.02

X7.8425 Y.5357 Z13.7198 C65.504 B-40.003 F49.99

X7.8682 Y.597 Z13.6984 C62.196 B-40.006 F49.99

X7.8936 Y.6442 Z13.6772 C59.145 F50.03

X7.918 Y.6788 Z13.6565 C56.32 B-40.003 F50.01

X7.9416 Y.7025 Z13.6365 C53.692 B-40. F49.99

X7.9679 Y.7304 Z13.6145 C50.941 F49.98

X7.9962 Y.7592 Z13.5908 C48.136 B-40.002 F50.01

X8.0234 Y.7775 Z13.5681 C45.522 B-40.003 F50.

X8.0488 Y.7863 Z13.5467 C43.086 F49.98

X8.0723 Y.7864 Z13.5269 C40.815 B-40.001 F50.01

X8.0943 Y.7789 Z13.5084 C38.694 B-40. F50.02

X8.1183 Y.7779 Z13.4883 C36.394 B-40.001 F50.

X8.1414 Y.7715 Z13.469 C34.192 B-40.002 F49.99

X8.1623 Y.7568 Z13.4514 C32.161 F50.

X8.1808 Y.7344 Z13.4359 C30.294 F49.98

X8.1971 Y.7049 Z13.4222 C28.582 B-40.001 F49.98

X8.2116 Y.6703 Z13.4099 C26.979 B-40. F50.01ut

 

[ 06-17-2002, 08:23 PM: Message edited by: gcode ]

[cadcam]

I am confused by the two diffrent files and typs of cut.

I am trying to understand what exactly you want.

Are you looking for code that will work either one?

 

Ok I put some new code from your files under the All NC Files.

 

Is this more of what you want?

 

What is the tilt limmit on this machine?

And are the axis A & B or B & C

 

[ 06-18-2002, 01:07 AM: Message edited by: cadcam ]

[Scott Bond]

Hi all

Gcode

Gcode ,that is a good idea for cutter path. and now I am thinking that I have a post problem.

Cadcam

quote:

---

I am confused by the two diffrent files and typs of cut.

---

Cadcam the first one is from me,and the next is from Gcode.

quote:

---

I am trying to understand what exactly you want.

---

Thanks for your file and your input,and now I am thinking that I have a post problem. Jay do you think any MC dealers have a post that we could get today for

Mitsu Seiki HUG3a-5x Horzontle A=110 B=360

Today we would need the post to make our shape, and the bells and whistle parts of the post could come later.

Scott

[cadcam]

Scott contact Glen this could be possable.

 

7372 Prince Drive, Suite 104

Huntington Beach, CA 92647-4573

Ph: 714-847-6890

Fax: 714-847-6833

 

I will be inclass from 7:30 to 11:30 am then open tell about 3:45pm then anoter class.

 

Oh I am not so confused any more. you were just using these examples to show the bad code out put.

 

[ 06-18-2002, 09:58 AM: Message edited by: cadcam ]

[Scott Bond]

Thanks all

I left a message with Glen.

What time is tonights class?

Do I bring anything?

[cadcam]

pm and no. just your self we have a seat there for you.