No experience with Industrial. Check out Blurry Customs. Nice folks to deal with and a top product.

Can we download the program so I don't have to go online to do the conversions?

Does anyone have some good advice on drilling out some fairly deep holes in plexiglass? The holes are 380mm (about 15 inches ) deep and 25MM( 1 inch) in diameter? The block is about 17.7 inches tall and 4 inches thick and 9 inches wide. The current options are in a manual lathe or a CNC knee mill but I would have to use both the spindle and knee movements to travel 15 inches deep. Need to drill 2 holes in each block... 14 blocks to begin and 98 blocks total.. Thinking about buying a small radial drill press as an option. It has been years since I have drilled any and the last time I used a radial drill press, piloted with a 1/2 drill and the slowly drilled the one inch to size... worked but very slow... only had to do two holes back then. Any ideas? Thanks

Thanks. Sounds like I will be purchasing several thread mills. I will need to machine some smaller NPT threads and Some straight metric threads also. Recs on brand of thread mills? Does anyone have a link to some charts for the hole sizes To cover standard,metric and NPT other than Machinist Handbook? I am guessing someone may have a link or a spread sheet Done already. As always. Thanks for your time and advice!!

I need advice on milling some 2 1/2 - 8 TPI female NPT threads in Plexiglass Full Depth. This will be my first time so be kind The project: 20 each 2 1/2 NPT female holes in Plexiglass. Options to consider? Bore hole. Mill taper profile with endmill, then thread with single point tool? Will it follow tapered profile? Bore hole, thread with Tapered Thread mill? Each part will have about 10 plus hours into the process when it comes time to cut the threads so...... Suggestions please Thanks

I had the same issue I installed two issues previouse of the Intellipoint mouse driver and all works fine now. I will look up the version if you need it. I am at work and the problem was on the home puter running win 7 64 bit. Let me know

I ran the 2 and 3 axis mill from Southwestern Industries and they run fine.Very easy to program "canned" ops at the control. The Route 66 mills are pretty neat also.

I hate to say it.. but did you install Art?

I got mach 3 mill. The SW ind stuff is all stock.

I have upgraded my controls on my home unit from SouthWestern Industries Prototrak Plus and MX3e controls to Mach 3 controls. Anyone have a need for the old stuff as spare part? All motors and ball screws have been reused ( low Hours) but the other stuff may come in handy as replacement parts. Contact me by email if interested.d Thanks

Is there a way to view the home position that I set in in the Toolpath parameters page setting. Point being, I set a home position relative to the part for a tool change and not using the home position set by the home switches on the mill. I would like to verify that the point I am setting is where the tool travels to for the tool change and not a machine home type coordinate that is dependent on home switches. By verify, I am asking is there a setting in the back plot or verify screens that will show the tool moving to the coordinate I set. Or is the a way to check the code and assure the position for tool change is correct. As always... Thanks for your time

I am trying to help my friend with his first mold. Also, this is my first mold. Very limited experience with the MasterCam and the new toolpaths. The ops that I selected are based upon my best guess. I need some advice on if I am heading the right direction on toolpaths or is there a much better way? Now the qualifiers are out of the way. Material: 7075 Alum Machine:

Thanks for all the help. I will need to find some more info on the correct method to select the drive surfaces, because I believe I am selecting them wrong. However, we ran the file on another Centroid Control and it ran fine with a round bottom. We have contacted Centroid dealer to find out what settings could be different between the two mills. The mill the file does not run on correctly has the most current upgrade on the SW but some settings must be skewed. Thanks again for your help. I need to do some more reading on the toolpath selection options and processes.

Not sure if this is what you wanted to see or not. First time posting a picture. hehe

Rough with a flat 1/4 finish with 1/4 ball and 1/8 ball end mills.

I am trying to help a friend with his first mold. And of course this is my first try to put a tool path to a mold file. The bottom of the cavity starts out round but then begins to flatten out to about 1/4 or 3/8 flat bottom and we need it to be rounded. I have tried different selecting the tool path geo different but still get the flat bottom. The model file is round but for some reason I am producing the flat bottom. Can someone explain how to make the correct changes. Since file is too large ( 2.7 m zipped) to upload I can email or other options. Thanks Ken

I am trying to produce some files for my friend. He is running a Centroid Controller. CNC 10 Mill Ver 1.21. Which post processor should we try and are there any immediate tweaks or setting that seem to work better than others. I will call Centroid during the work week to inquire about any software upgrades that may be available for the control so he will have the latest for his control. Thanks Ken

Thanks, JP. Painless so far

Win 7 Enterprise Microsoft wireless wheel mouse MasterCam X4 and X5(just loaded) Trying to use the mouse wheel to zoom in and out. No matter which way I rotate the wheel all I get is a Zoom out result. The zoom works in all other programs. Can anyone tell me a setting to check and modify in MasterCam. Thanks Ken

Can anyone help with a "Vine of LIfe" pattern link? I am trying to cut a pattern into a guitar neck. Thanks

I am looking for a blue print to build a copy of a 1952 Fender Telecaster. My plan is to make a 3 d model from the drawing and then use the mill (3 axis) to make the body. Can anyone point me to a resource for the info/ project? Thanks

Josh, Mail is being returned by your post office box. Thanks