Thanks for all the help I got the one side to work and have made some extensive trim changes. now I am trying to get the geometry mirrored to get the other side to work. I mirrored the Spline chain but MC crashes when processing ... so I am going to mirror the axis control surfaces and see what happens.

John, Nope geometry created in SW2009 imported into MC SLDPRT to MC If I remember correctly. Solid body then I created surfs from solid faces.

I have been working on it and got one toolpath to work and mirrored the geometry for the other side and MC has been crashing. I opened up the file I posted on the FTP and tried the break at point. And MC crashed again WTF !!! Where did you guys break the Spline ??

bump

just posted a ZipToGo file on the FTP in MCX_files RXVFRONTPROB.Z2G it is operations #6 and #8

when I do a chain analysis it comes back one spline 62.3373 inches long sounds right.... is there any other way to check for gaps ??

Colin, Just tried the look ahead.... Nope.

John Yes I tried moving the start point to the middle of the section it will not cut.. No change. Colin, I will give that try

John it selects all as one... can it do that if it is not one piece ?? I have to share the Hasp with another programer when I get it back I can look again to see if there is a break.... I think that there is not

I am trimming a part and I have a 5 axis curve toolpath. I have a single spline for the curve and 2 surfs for tool axis it cuts all around except for one side what is wrong that is causing this ??

Thad See my second post

Dan Thanks for the reply. But I am trying to project Normal to the surface. I got it to work by first doing a 2D trim to bring it close. Or maybe change the entity ID ??? IDK but after that MC was able to project the curve onto the surface so I am back in business.

I created a edge curve and offset it 0.050" away from the edge of the surface and now I want to "snap" the curve back normal to the surface. where it now would lay. My dealer and I did this with my file on his machine while on GotoMeeting, this AM but now he is at a on site training. and as luck would have it I can not get MC to do it on my computer. MC says no projections found. I tried closing and re opening MC still will not do it.

We have a Gmail corp. account I will try to send. I ref. this thread for the pics.

that email is [email protected] right ??? My ZipToGo file is 15MB will that email ??

here is a pic of the final cut made with the surface from solid.

Gcode No both rough and finish from the SOLID were bad. Surfaces from solid face were GOOD. I refinished using the Surface from solid face and the surface cut proper. they look congruent on the screen but the solid cut further OUT and the surface cut IN where it should. kind of scary what if the solid cut the other way ???

Ok guys here is what I found: first these were constant Z Rough and finish high speed toolpaths. No rapids just around and step down and around and down again... and again.... I was using a imported Solid ( .X_T ) from SW 2007 that did have some "issues" (faces sticking out like untrimmed surfaces) When I created Surfaces from Solid faces to do some pencil toolpaths they were cutting in to the finished surfaces. (from the solid) So I started thinking maybe the solid was creating a bad toolpath (too far out) So I used the surfaces that I created from the solid faces with standard contour surface finish and re cut the bad area and .......... All is good everything cleaned back up. only thing I can figure is that there was something wrong with the Solid ???

No what I mean is that the roughing passes were actually below (inside) the drive surface. the general area inside the red is where it screwed up. seems simple enough ???

The X3 MU1 High Speed Rest Rough gouged my part even with 0.050" stock to leave I was using a solid for starting stock (not a simple rectangular block). WTF !!! on an area about the size of my palm on a mold 32" x 37" x 14" tall. Is this a problem with the High speed toolpaths ?? Verify looked Great !!!! part ended up not so much.

yep, I got the same issues with X3 thought a new vid driver would help but it did not

thanks Tyler.... It never hurts to have to many "go to" guys to be able to bounce questions off. thanks again Mike from KMT is doing a web demo on one of our parts tomorrow... that should help a lot.

Tyler, Yes I have dome some customizing of posts... not a lot but some. Again to date all programs have been hand taught and may or may not be "Proper" this was one of the first 3 or 5 machines RPT built. We are having a web demo this Friday and the guy from KMT is going to help get the post tweaked and go though the full process. If I need some additional help I would like to be able to call on your expertise. thanks for your intrest in helping

This is code as output from RobotMaster (not the same program and only one operation) /PROG A095904R /ATTR OWNER = MNEDITOR; COMMENT = "BY ROBOTMASTER"; PROG_SIZE = 0; CREATE = DATE 08-10-28 TIME 14:05:10; MODIFIED = DATE 08-10-28 TIME 14:05:10; FILE_NAME = ; VERSION = 0; LINE_COUNT = 40; MEMORY_SIZE = 0; PROTECT = READ_WRITE; TCD: STACK_SIZE = 0, TASK_PRIORITY = 50, TIME_SLICE = 0, BUSY_LAMP_OFF = 0, ABORT_REQUEST = 0, PAUSE_REQUEST = 0; DEFAULT_GROUP = 1,*,*,*,*; CONTROL_CODE = 00000000 00000000; /MN 1: UFRAME_NUM = 1 ; 2: UTOOL_NUM = 1 ; 3: CALL ; 4: CALL AA_ON ; 5:J P[1] 50% FINE ; 6:J P[2] 50% FINE ; 7:J P[3] 50% FINE ; 8:J P[4] 50% FINE ; 9:L P[5] 200 mm/sec FINE ; 10:L P[6] 200 mm/sec CNT100 ; 11:C P[7] P[8] 200 mm/sec CNT100 ; 12:C P[9] P[10] 200 mm/sec CNT100 ; 13:L P[11] 200 mm/sec CNT100 ; 14:C P[12] P[13] 200 mm/sec CNT100 ; 15:L P[14] 200 mm/sec CNT100 ; 16:C P[15] P[16] 200 mm/sec CNT100 ; 17:L P[17] 200 mm/sec CNT100 ; 18:C P[18] P[19] 200 mm/sec CNT100 ; 19:L P[20] 200 mm/sec CNT100 ; 20:C P[21] P[22] 200 mm/sec CNT100 ; 21:L P[23] 200 mm/sec CNT100 ; 22:C P[24] P[25] 200 mm/sec CNT100 ; 23:L P[26] 200 mm/sec CNT100 ; 24:L P[27] 200 mm/sec CNT100 ; 25:C P[28] P[29] 200 mm/sec CNT100 ; 26:C P[30] P[31] 200 mm/sec CNT100 ; 27:L P[32] 200 mm/sec CNT100 ; 28:C P[33] P[34] 200 mm/sec CNT100 ; 29:L P[35] 200 mm/sec CNT100 ; 30:C P[36] P[37] 200 mm/sec CNT100 ; 31:L P[38] 200 mm/sec CNT100 ; 32:C P[39] P[40] 200 mm/sec CNT100 ; 33:L P[41] 200 mm/sec CNT100 ; 34:C P[42] P[43] 200 mm/sec CNT100 ; 35:L P[44] 200 mm/sec CNT100 ; 36:C P[45] P[46] 200 mm/sec CNT100 ; 37:J P[47] 50% FINE ; 38: CALL AA_OFF ; 39:J P[48] 50% FINE ; 40:J P[49] 50% FINE ; /POS P[1]{ GP1: UF : 1, UT : 1, J1= -35.48 deg, J2= -1.03 deg, J3= 22.78 deg, J4= 120.37 deg, J5= 42.42 deg, J6= -37.02 deg }; P[2]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 87.38 mm, Y = -187.32 mm, Z = 254.00 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[3]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 87.38 mm, Y = -187.32 mm, Z = 101.60 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[4]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 87.38 mm, Y = -187.32 mm, Z = 2.54 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[5]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 87.38 mm, Y = -187.32 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[6]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 87.38 mm, Y = -111.12 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[7]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 65.06 mm, Y = -57.24 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[8]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 11.18 mm, Y = -34.92 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[9]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = -21.42 mm, Y = -21.42 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[10]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = -34.92 mm, Y = 11.18 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[11]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, -1', X = -34.92 mm, Y = 317.76 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[12]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, -1', X = -32.14 mm, Y = 333.53 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[13]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, -1', X = -24.14 mm, Y = 347.40 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[14]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, -1', X = 46.19 mm, Y = 431.21 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[15]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, -1', X = 62.02 mm, Y = 443.35 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[16]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, -1', X = 81.51 mm, Y = 447.67 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[17]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, -1', X = 536.45 mm, Y = 447.67 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[18]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, -1', X = 569.04 mm, Y = 434.17 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[19]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, -1', X = 582.55 mm, Y = 401.57 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[20]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 582.55 mm, Y = 11.18 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[21]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 569.04 mm, Y = -21.42 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[22]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 536.45 mm, Y = -34.92 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[23]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 11.18 mm, Y = -34.92 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[24]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 10.41 mm, Y = -34.92 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[25]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 9.65 mm, Y = -34.90 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[26]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 87.38 mm, Y = -187.32 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[27]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 87.38 mm, Y = -111.12 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[28]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 65.06 mm, Y = -57.24 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[29]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 11.18 mm, Y = -34.92 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[30]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = -21.42 mm, Y = -21.42 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[31]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = -34.92 mm, Y = 11.18 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[32]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, -1', X = -34.92 mm, Y = 317.76 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[33]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, -1', X = -32.14 mm, Y = 333.53 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[34]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, -1', X = -24.14 mm, Y = 347.40 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[35]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, -1', X = 46.19 mm, Y = 431.21 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[36]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, -1', X = 62.02 mm, Y = 443.35 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[37]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, -1', X = 81.51 mm, Y = 447.67 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[38]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, -1', X = 536.45 mm, Y = 447.67 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[39]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, -1', X = 569.04 mm, Y = 434.17 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[40]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, -1', X = 582.55 mm, Y = 401.57 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[41]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 582.55 mm, Y = 11.18 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[42]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 569.04 mm, Y = -21.42 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[43]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 536.45 mm, Y = -34.92 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[44]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 11.18 mm, Y = -34.92 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[45]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 10.41 mm, Y = -34.92 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[46]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 9.65 mm, Y = -34.90 mm, Z = -2.29 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[47]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 9.65 mm, Y = -34.90 mm, Z = 101.60 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[48]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 9.65 mm, Y = -34.90 mm, Z = 254.00 mm, W = 180.00 deg, P = 0.00 deg, R = 0.00 deg }; P[49]{ GP1: UF : 1, UT : 1, J1= -35.48 deg, J2= -1.03 deg, J3= 22.78 deg, J4= 120.37 deg, J5= 42.42 deg, J6= -37.02 deg }; /END

Tyler, Thanks for the reply here is a program with calls hand taught. /PROG ANS00001 /ATTR OWNER = MNEDITOR; COMMENT = "M985A CECILWARE "; PROG_SIZE = 3472; CREATE = DATE 05-06-02 TIME 02:30:22; MODIFIED = DATE 08-08-05 TIME 13:17:11; FILE_NAME = ; VERSION = 0; LINE_COUNT = 114; MEMORY_SIZE = 3960; PROTECT = READ_WRITE; TCD: STACK_SIZE = 0, TASK_PRIORITY = 50, TIME_SLICE = 0, BUSY_LAMP_OFF = 0, ABORT_REQUEST = 0, PAUSE_REQUEST = 0; DEFAULT_GROUP = 1,*,*,*,*; CONTROL_CODE = 00000000 00000000; /APPL AUTO_SINGULARITY_HEADER; ENABLE_SINGULARITY_AVOIDANCE : TRUE; /MN 1: !TOOL 6 .250 DOWNSPIRAL ; 2: !TOOL 4 .218 DRILL ; 3: !TOOL 3 .250 DRILL ; 4: ; 5: TIMER[1]=RESET ; 6: TIMER[1]=START ; 7: ; 8: JMP LBL[99] ; 9:J P[1:U_FRAME INFO] 1% FINE ; 10:J P[2:O] 10% FINE ; 11:J P[3:X] 10% FINE ; 12:J P[4:Y] 10% FINE ; 13: LBL[99] ; 14: ; 15: !put the data into a temp PR ; 16: PR[8]=P[1] ; 17: !Set desired uframe w/ data ; 18: UFRAME[1]=PR[8] ; 19: !invoke desired uframe as active ; 20: ; 21: UFRAME_NUM=0 ; 22:J PR[81] 100% CNT100 ; 23:J PR[82] 100% CNT100 ; 24: R[31]=6 ; 25: CALL SEL_TOOL ; 26: AO[1]=1500 ; 27: CALL AA_ON ; 28:J PR[82] 100% CNT100 ; 29: UFRAME_NUM=1 ; 30: ; 31:J P[5] 100% CNT100 ; 32:J P[6] 100% CNT100 ; 33: ; 34: JMP LBL[29] ; 35:J P[7] 100% CNT100 ; 36: CALL M985_1('FLANGE TRIM') ; 37: LBL[29] ; 38: ; 39:J P[8] 100% CNT100 ; 40:J P[9] 100% CNT100 ; 41:J P[10] 100% CNT100 ; 42:J P[11] 100% CNT100 ; 43:L P[12] 4000.0inch/min CNT100 ; 44: ; 45: CALL M985_2('PART TRIM') ; 46: ; 47:L P[13] 4000.0inch/min CNT100 ; 48:L P[14] 4000.0inch/min CNT100 ; 49: ; 50: CALL M985_3('CUP CUTOUT') ; 51: ; 52:L P[15] 4000.0inch/min CNT100 ; 53:L P[16] 4000.0inch/min CNT100 ; 54:L P[17] 4000.0inch/min CNT100 ; 55: ; 56: CALL M985_4('RECT. CUTOUT') ; 57: ; 58:L P[18] 4000.0inch/min CNT100 ; 59: ; 60: CALL M985_5('SLOT 1 CUTOUT') ; 61: ; 62:L P[19] 4000.0inch/min CNT100 ; 63: ; 64: CALL M985_6('SLOT 2 CUTOUT') ; 65: ; 66:L P[20] 4000.0inch/min CNT100 ; 67: ; 68: CALL AA_OFF ; 69: UFRAME_NUM=0 ; 70:J PR[82] 100% CNT25 ; 71: R[31]=4 ; 72: CALL SEL_TOOL ; 73:J PR[82] 100% CNT100 ; 74: UFRAME_NUM=1 ; 75: AO[1]=100 ; 76: CALL AA_ON ; 77: ; 78:J P[21] 100% CNT100 ; 79:J P[22] 100% CNT100 ; 80:J P[23] 100% CNT100 ; 81: ; 82: CALL M985_7('DRILL FRONT') ; 83: ; 84:L P[24] 4000.0inch/min CNT100 ; 85:J P[25] 100% CNT100 ; 86: ; 87: CALL AA_OFF ; 88: UFRAME_NUM=0 ; 89:J PR[82] 100% CNT25 ; 90: R[31]=3 ; 91: CALL SEL_TOOL ; 92:J PR[82] 100% CNT100 ; 93: UFRAME_NUM=1 ; 94: AO[1]=100 ; 95: CALL AA_ON ; 96: ; 97:J P[26] 100% CNT100 ; 98:J P[27] 100% CNT100 ; 99:J P[28] 100% CNT100 ; 100: ; 101: CALL M985_8('DRILL SIDE') ; 102: ; 103:J P[30] 100% CNT100 ; 104: ; 105: CALL AA_OFF ; 106: UFRAME_NUM=0 ; 107:J PR[82] 100% CNT25 ; 108: R[31]=0 ; 109: CALL SEL_TOOL ; 110:J PR[82] 100% CNT100 ; 111:J PR[81] 100% CNT100 ; 112:J PR[80] 100% FINE ; 113: ; 114: TIMER[1]=STOP ; /POS P[1:"U_FRAME INFO"]{ GP1: UF : 1, UT : 1, CONFIG : 'N D B, 0, 0, 0', X = 1548.174 mm, Y = 128.037 mm, Z = 287.898 mm, W = 129.662 deg, P = 88.312 deg, R = -50.112 deg }; P[2:"O"]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, -1, 0', X = .032 mm, Y = -.003 mm, Z = .000 mm, W = -179.666 deg, P = -1.234 deg, R = -.268 deg }; P[3:"X"]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, -1, 0', X = 248.184 mm, Y = .011 mm, Z = .005 mm, W = -179.672 deg, P = -1.233 deg, R = -.250 deg }; P[4:"Y"]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, -1, 0', X = -.278 mm, Y = 198.004 mm, Z = 0.000 mm, W = -179.662 deg, P = -1.232 deg, R = -.274 deg }; P[5]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = -637.000 mm, Y = 468.518 mm, Z = 749.296 mm, W = 93.717 deg, P = 26.553 deg, R = -170.729 deg }; P[6]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = -637.002 mm, Y = 265.120 mm, Z = 749.295 mm, W = 124.773 deg, P = 26.516 deg, R = 138.913 deg }; P[7]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = -368.800 mm, Y = 265.123 mm, Z = 256.088 mm, W = 176.127 deg, P = -9.029 deg, R = 28.363 deg }; P[8]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = -245.424 mm, Y = -412.934 mm, Z = 720.433 mm, W = -165.717 deg, P = 86.872 deg, R = 167.809 deg }; P[9]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = -245.425 mm, Y = -412.933 mm, Z = 720.435 mm, W = -165.716 deg, P = 86.873 deg, R = 76.456 deg }; P[10]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = -237.357 mm, Y = -416.113 mm, Z = 722.970 mm, W = -148.027 deg, P = 88.766 deg, R = 27.869 deg }; P[11]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, -1', X = 381.843 mm, Y = -416.112 mm, Z = 590.492 mm, W = -148.026 deg, P = 88.766 deg, R = 27.869 deg }; P[12]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 381.844 mm, Y = -416.112 mm, Z = 190.172 mm, W = -148.027 deg, P = 88.766 deg, R = 27.869 deg }; P[13]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 321.263 mm, Y = -432.847 mm, Z = 677.434 mm, W = -150.897 deg, P = 88.829 deg, R = -59.927 deg }; P[14]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 148.709 mm, Y = -247.398 mm, Z = 70.010 mm, W = -173.186 deg, P = 50.733 deg, R = -96.640 deg }; P[15]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 147.055 mm, Y = -253.398 mm, Z = 435.033 mm, W = -173.186 deg, P = 50.732 deg, R = -96.640 deg }; P[16]{ GP1: UF : 1, UT : 1, CONFIG : 'N U T, 0, 0, 0', X = 134.539 mm, Y = -95.924 mm, Z = 454.691 mm, W = -179.691 deg, P = -1.188 deg, R = 68.324 deg }; P[17]{ GP1: UF : 1, UT : 1, CONFIG : 'N U T, 0, 0, 0', X = 90.290 mm, Y = -4.939 mm, Z = 187.423 mm, W = -179.688 deg, P = -1.180 deg, R = 68.330 deg }; P[18]{ GP1: UF : 1, UT : 1, CONFIG : 'N U T, 0, 0, 0', X = 30.088 mm, Y = -127.247 mm, Z = 187.242 mm, W = -179.688 deg, P = -1.180 deg, R = 68.330 deg }; P[19]{ GP1: UF : 1, UT : 1, CONFIG : 'N U T, 0, 0, 0', X = 161.957 mm, Y = -129.546 mm, Z = 191.690 mm, W = -179.688 deg, P = -1.180 deg, R = 68.330 deg }; P[20]{ GP1: UF : 1, UT : 1, CONFIG : 'N U T, 0, 0, 0', X = 214.566 mm, Y = 369.605 mm, Z = 594.341 mm, W = -174.634 deg, P = -.026 deg, R = 69.651 deg }; P[21:""]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = -317.732 mm, Y = 402.659 mm, Z = 651.346 mm, W = 108.633 deg, P = 50.111 deg, R = 122.326 deg }; P[22]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = -201.168 mm, Y = 311.538 mm, Z = 559.651 mm, W = -179.915 deg, P = 10.697 deg, R = 57.511 deg }; P[23]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, -1, 0', X = 128.110 mm, Y = -32.256 mm, Z = 559.586 mm, W = 176.268 deg, P = .326 deg, R = -7.675 deg }; P[24]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, -1, 0', X = 49.198 mm, Y = -15.255 mm, Z = 521.242 mm, W = 179.217 deg, P = .643 deg, R = -7.650 deg }; P[25]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = -147.651 mm, Y = 275.202 mm, Z = 541.940 mm, W = 177.865 deg, P = 2.488 deg, R = 54.956 deg }; P[26]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = -250.356 mm, Y = 638.522 mm, Z = 519.087 mm, W = 161.935 deg, P = 53.466 deg, R = 152.617 deg }; P[27]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = -356.102 mm, Y = 389.129 mm, Z = 582.679 mm, W = -105.887 deg, P = 64.391 deg, R = 175.241 deg }; P[28]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = 264.897 mm, Y = 491.726 mm, Z = 389.075 mm, W = -110.148 deg, P = 87.285 deg, R = 165.548 deg }; P[30]{ GP1: UF : 1, UT : 1, CONFIG : 'F U T, 0, 0, 0', X = -249.474 mm, Y = 344.802 mm, Z = 705.685 mm, W = -96.301 deg, P = 87.704 deg, R = -4.802 deg }; /END