desmotom
-
Posts
137 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Store
eMastercam Wiki
Blogs
Gallery
Events
Posts posted by desmotom
-
-
Has anyone ever turned an eccentric on a lathe. The eccentric is turned from bar stock with concentric journal next to the eccentric one. Tolerance is not an issue, the part will be sent out for grinding. I was thinking of using a milling cutter and the c axis to interpolate it.
-
Yeah the have a chip breaker. They are full form insert. I used three spring passes and 60 angle. It seems to be good but not great. Using a 55 degree pull out angle effect my thread form?
-
I had tried it a 29 angle but I had the same results. What about rpm?
-
Yup its magnetic. How does my cycle look?
-
I am threading with a center. How would I go about adding finishing passes. I didn't know you could do that, I only added spring passes.
-
Have trouble with chatter on threading stainless 1.1258tpi its tougher grade of stainless not sure exactly what grade not called out on drawing
N10(THREADING )
(USE SANDVIK THREADING INSERT 8 TPI)
(USE SANDVIK THREADING HOLDER)
(TOOL PROTRUSION)
( UPPER TURRET )
( SUB SPINDLE )
G0G30U0W0
N6G55T1010
M414
G97S500M54
G18U0.W0.
G0G99X5.0Z-.1M8
X1.13
G76 P020160 Q0030 R.001
G76 X.9717 Z2.6P 0767Q0300 F.125
G0X1.6361
Z-.1M9
G0X5.0
G30U0W0
M5
M55
M71
G30U0W0
M115
M30
-
thanks mike, this forum is awesome thanks for the help guys...anyone need their car washed:)
-
Yes I did thank you.
-
Need some help with M codes for transfering
-
I'll try him, thanks.
-
Nope not that guy.
-
How can I get a hold off this Cris M?
-
Just started with a new company which has a Nakamura Tome WT 250 which nobody knows how to utilize. I am trying to find the proper format and codes to transfer from main to sub and quill support function. Any help would be greatly appreciated.
-
I have the NT Nurse, what do you mean by template?
-
Not very good allan, I miss mastercam, I might be reunited in the near future.....
-
Looking for help with a transfer sequence for a Nakamura Tome WT 250 twin spindle lathe. Does anyone have any experince with them?
-
Their top gibbs guy has four months exp. with no machining background. I will be their top gibbs err mc guy in the future.
Geometry is a pain to create!!
-
I am already trying to convince them that MC is the way to go, but they just signed a new contract with gibbs. Pulling my hair out trying to create geometry, the whole program is too vague.
-
Starting a new job on Monday they only have Gibbs, at least I get to learn a new software, but already I can see how much more powerful MC is than Gibbs.
-
Make sure the red operation arrow in the operations manager is at the bottom of all operation or else you will see "shadow" of the first side. I use stock flip all the time and usually don't have any problems with it.
-
thanks for the info going to run it today
-
Its g code macro for engraving sequential serial numbers on the outside of a 5.5 inch dia tube. Never used a macro before but the forum has been a big help.
-
I am running a Fanuc control I will try that. Any tip on setting up the program.
-
I made a macro program for sequential engraving with the help of the forum, now I am not sure where I put the programs in the control. Are they just in the program below the main program?
Eccentric turning
in Industrial Forum
Posted
I was hoping to get it done in one setup. That was they way I was going to go in two ops. I would save so much time in one op though.