I am get to ikea post from mastercam,web the haas and fonuc and still posting wrong

SOo I am set up my angle head in my mashie deff when I oposting code looks like is something wrong ,the ,how I can change Y to Z? HMC SAMPLE.MCAM-CONTENT

Thank you ,let me take look

Hello ,someone programing it ? I need to cut keway on big cam

Thank you for reply I think we find out this one

Hello We try set up a aure HMC with tosnuc 732 control, when I load the program I start running, the alarm show up Anybody can help what is the problem ?

Are use 2024 ?

What about this setting

tank you for your reply ,when I use this option pick up all holes like on the picture

Hello All ,how I can pick up holes only on my blue face ,when I use ctrl shift mastercam pick up all the same holes on on my front face what I am working and on the back face . thanks for any helps

I can use the 3d toolpath for finish from the small holes side ,but the will be very hard use sime enmill for other side ,I need over 6 inch long enmill I am still didnt see this

ok ,I think I see some flats on my stock is beacos I am make to deep 3 inch hole on my lathe on face thats why I have problem for blend it all together can you run your toolpath on my stock for blend oper ?

I an use the same thing and still do not work for me

what toolpath are using here ?

But when I try to use 3d contour toopath for finish this I can see the will be still som flat section on the part

I don't know how I can explain this to you I have this mdel from the costumer .So my plan was to set up this for lathe ,turn od and make face bore 1st .So after that I am creating working plan from the center line of side bore and I am use helix toolpath for rough .When I am make veryfy I see the I I can't go all to the bottom becose I will hits in the wall of the face bore , So ,I am create other operation and working plane and try use some rough 3d toopkath and 3 finish ,but I don't know haw I can finish this with rhe same results what solid For me this is not doable

I thought so

UBST-UIC-009-05_REV1.MCAM-CONTENT

Can some one can help me on this sample , I am open old program ,the other program marck one hole and rotate toolpath around x I am try ise 5 axis drilling marck all holes but do not work , 4 TH AXIS DRILLING.MCAM-CONTENT ok ,got it

Can you check this one ? B09470-2.MCAM-CONTENT

B09470.MCAM-CONTENT B09470.mcam

Hello All I need to find out what happen on my VTL set up .Yesterday when I am start program part all roll over on my X value , This is my set up Vtl see pic Till yesterday everything working fine my post posting positive x value like as should , today I am start mastercam and all x axis are negative ,even when I am open my old good programs the axis are now wrong .I am use generic VTL post and machine deff from mastercam web . This my code ,all X are negative (TOOL - 3 OFFSET - 3) (RIGHT TURRET - 80 DEG. INSERT - CNMG-432) (FACE) G0 T0303 G18 M8 G97 S50 M03 G0 G54 X-30.31 Z.1 G50 S200 G96 S400 G99 G1 Z0. F.015 X-26.81 X-26.9514 Z.0707 M9 G28 W0. M05 T0300 M01 (TOOL - 3 OFFSET - 3) (RIGHT TURRET - 80 DEG. INSERT - CNMG-432) (OD CHAMFER) G0 T0303 G18 M8 G97 S52 M03 G0 G54 X-29.2796 Z.1969 G50 S200 G96 S400 G1 Z.0969 F.015 X-30.416 Z-.4713 X-30.5574 Z-.4006 M9 G28 W0. M05 T0300 M01 what I am doing wrong ,did I am change something ????

I am use morph

Hello ,its work ?

Hello All, what is the best toolpath for this shape off gear .I can use the swarf because the I will be cut the 2nd part (mirror ) in the deep packet