JAWI11

WELCOME TO THE CLUB,I HAVE THE SAME PROBLEM , I would like to start doing something on   5 axis but  I can not find any good videos or books .My re seller said that maybe will help me in the shop working with my on part ,but for now we do not have any typical job for 5 axis ,and the second problem is that we do not have purchased a license for 5 axis.I can not say  to the  boss ,  To close all shop   just for me  buy  licenses      because i wants to call for my reseller and play on 5 axis part .I think   I stuck , and when I have something on indexer running on    I   , rotate and use surfaces toolpath

 I WAITING FOR EMAIL FROM THEM    ALL DAY AND   NOTHING.TIME CHANGE RESELLER

THANKS

Hi everyone!!!!

can anyone help me with my postproprocesor, I would like to change a few things

N14 ( LTR. Y CARBIDE  DRILL   T14 , D14 , H14 , ACT DIA.= .404 )G0 G90 G54 X-1.3756 Y5.1339 S2250 M3G43 H14 Z2.M88G98 G81 Z-2.0718 R.1 F14.X1.3756 Y-5.1339G0M9M5G91 G28 Z0.G28 Y0.M30

1.I would like to have speed in the next line

2.does not generate me M89 a s it should be and coolent M89  have in earlier line

AS BELOW:

G0 G90 G54 X-1.3756 Y5.1339S2250 M3G43 H14 Z2.M88G98 G81 Z-2.0718 R.1 F14.X1.3756 Y-5.1339G0 Z2. M89M5G91 G28 Z0.G28 Y0.M30

THANK YOU FOR ALL ANSWERS

4/25.4  THIS IS YOURS PITCH AND WHAT TOOL YOU WONT TO USE 1 POINT OR MULTI POINTER ????SET THE DEEP AND DONE

THIS IS POST FOR HAAS ,AND THIS IS ONLY SAMPLE OF TOOLPATH 

you can use this toolpath

V6 TOP.mcx-9

WHAT MATERIAL ????

YOU WONT TO MAKE SHOW ONLY ON MASTERCAM ,OR SET UP ON SOME MACHINE ????

OK , I HAVE NOW THANKS

THANK YOU ALLAN

BUT WHY NOT  SHOWS ME THAT ON SIMULATOR

Halo everyone!!!

I have a question,if there is an option to do this  oil grove on lathe .I am mill gay and i now the part is to long for set up on mill.

Thank you for any suggestions

200892.mcx-9

Is there any option in control def ?????

 THIS IS MILL 

THESE CODES G91G28Z0

G28Y0

I want them only at the end of program

HELLO ,

I WANT TO  SEND MACHINE  ON HOME POSITION  ONLY AFTER THE LAST  OPERATIONS

WHERE CAN I CHANGE POST???

interesting, under minute ????

thanks for the help , I have to do 80 pieces

HELLO EVERYONE !!!!

I want to use  One of the      surface high speed tollpath for my  part . material is ss 304  .I want to use  .5 DIA carbide enmill full depp  (1 inch high part).

which will be the best??? what step over and feed and speed I should???

Thank you for any ideas

THANK YOU FOR IDEAS

Hello everyone!!!!

Did any of  you  may can advise what  toolpat  ( tool)  choose to make this plate ???

I am looking for the best way cut SS material .what is the most effective???

I have a .125 stock  on  width and length around the contour.

THANKS

I a deal With COSTOMER  , and , I  can use 5/8 ENMILL   in the corners  Is not it better to use the      full deep and change toolpath on  MULTI PASSES?????

"

Also, I programmed a linear feed of 29 IPM, but the feed output in the code is F2000. for the cutting moves with the C axis"

WHAT ABOUT THIS , QUESTION  BECAUSE SOMETIMES RUNS 4 AXIS  IN AND HAVE THE SAME PROBLEM???

VERY HARD

YES

THIS MY MY MCX FILE

45-25.mcx-8

most problems i have with roughing teeth after welding ,I tried to use the .5 carbide finish enmill and i make 2 pcs .after rough i cut all contour i use .75 sumitomo insert emill ramping contour .025 step dawn .1500 rpm and 75 ipm .for rough teeth .5 carbide finish 2500rpm and 90 ipm  and .01 step dawn .