Register now to participate in the forums, access the download area, buy Mastercam training materials, post processors and more. This message will be removed once you have signed in.
Use your display name or email address to sign in:
Last side is possible in a Pocket Toolpath.
Wish list add last depth override and stepover.
Than you cann rough and finish Properly in one operation.
May be wish list for X6 also tool change.
Actually in the conversational programing for ***or (lathe) is included.
You set a geometry and than only feed,speed,tool and so on for Rough and the same set of parameter for finish.
I think this is not a big trouble for CNC.
Regards
I know about this deformations and also do this procedure (rough, turn the machining side, rough again and final finish, in this case I done this two times)
Actually the part has been Tempered treated before machining.
My question is if anybody has got any allowance.
How did you decide if the part is ok or not?
Which criterium did you use for take this decision
Jim:
Thanks for your answer.
Actually I have got a drawing.
My question is if there is a standard like DIN 7168 T1 for lenght.
DIN 7168 T1 is a standard for length, there you can see different Klasses, for example f,m,g and sg.
f (fein)
m (mittel)
g (grob)
sg(sehr grob)
And according to my job I decide what toleranz klass did I take.
I get a part 100" x 60" x 3" for milling.
The part had some grooves but mainly is a flat milled plate.
I have some paralism problems because the part bend or deform when i mill on both sides.
Did somebody have any experience what are normal tolerances for this paralelism.
I mean parcial and total paralelism.
Or were cann I found information about paralelism standards.
Thanks
Is there a viewer where I cann see Mastercam files.
Like Voloview for DWG files or oder products for inventor.
I just need to see the files actually is not important if I see toolpaths or tools.
i just need to see Mastercam files geometry.
Thanks
Terry:
Thanks for your answer but according to the software description can not be used for 64 bit Vista because only accepts signed drivers.
There is an option in vista to install without signed drivers verification. ¿Did you think this will work?
Or may be is another solution for 64 bit vista
Thank you very much in advanced
My old ***or 8055 only understand Netbeui Protocol but Windows Vista do not support it.
¿What cann I do?
¿I there a way to install Netbeui in Vista ??
Thanks
Is there any difference in the processing time between Vista and XP ??
I mean the same hardware with two different OS makes any difference in the proccessing time??
I´m looking for a new PC and they offer me the option XP or Vista
In both case will be 64 bit.
XL
Did In House send it to South America ???
By the way I broke my Mastercam coffe cup. Was my cup for 8 years. I miss my cup.
We don´t get any Mastercam gifts here.
If somebody had a Mastercam extra cup can send it to me. I will be very graetful.
Thanks in advanced
Leandro
Steve Why did you take the XEON and not Core 2 Duo ???
Is it better,faster ???
I´m looking for a new PC and in Buenos Aires we get a lot of Core 2 but not Xeon.
Thanks
Steve is this your CPU ???
Intel® Core™ 2 Duo Processor E6550/E6850
(2.33/3.0GHz, 65nm, FSB1066/FSB1333, 4MB L2 cache, LGA775)
http://www.clevo.com.tw/en/products/prodin...sp?productid=19
Juan:
Actually I´m looking for a Setup sheet for Lathe and the one from X+ looks pritty good.
Cann you advise me somthing ??
In advanced I thank you.
Leandro
Actually you don´t have an "option button" or something like that for the spindle rotation.
The spindle rotation depends only from your tool.
Check your tool, you will see in the "setup tool" page the spindle rotation. Oay atention when you change the spindle rotation changes also the position. Check this with the "draw tool" button.
I don´t know what is the "Negative X" never use it.
Juan,
I thank you very much. I agree with you if I need it more times I need the Catia translator. This is my first time with this type of file.
Question: Is posible that when you convert to MCX you change units from metric to inch?
Now I merge all the files into a metric file and get my metric files.
Again Thank you very much
Leandro
Ok. I upload the files on the ftp.
ftp://www.mastercam-cadcam.com/Mastercam_...solids/CatPart/
If somebody can convert I will apreciatte.
In advanced I thank you very much
Leandro
I get from my customer a file with the extension CATPart file
I suppose this is a CATIA file.
Can I send this file to somebody to convert in a Mastercam file please?? Could also be in iges or another format that can read in Mastercam
In advanced I thank you very much
Leandro
I´m tring to fillet two surfaces with a radius 5mm but I get every time the same error.
Now I´m using Create -> Surface -> Fillet -> To surface.
[/img]
What I´m doing wrong?
Thanks
eMastercam - your online source for all things Mastercam.
Together, we are the strongest Mastercam community on the web with over 56,000 members, and our online store offers a wide selection of training materials for all applications and skill levels.