I like watching porn, but my favorite types of porn are with gay men displaying their nude bodies and butts while engaging in mouth xxxxs and giving deepthroat blowjob. It makes me crazy to view more videos from best porn sites by https://bestpornsites.porn/

I love to watch Hardcore group sex because hot horny girls do group sex roughly.she wants group sex xxxxing with double penetration, threesome and foursome. She makes some horny noise that makes me crazy. I get more collection of top group sex videos from best porn sites by https://listofporn.com/

im trying to create some involute splines using the gear c hook. i use mastercam in metric mode, im assuming the gear dll is imperial only as when i measure the drawing after creating a 20 dp 15t 30 pa gear,(thats what my local gear cutting toolmaker measured the tooth form to be on a shadow projector even though the actual shaft splines are 25 tooth and 27.4mm od), its under 1mm od ? is there a way to correct this without converting all the parameters to mm ?

Is anyone here using this combination? I have a file transfer issue I am trying to resolve, and Cimco aren't being that helpful The issue is when sending the file back to Cimco, Cimco isn't receiving it, but leaving it in the "holding folder" because it isn't being renamed properly. I suspect it is a name trigger issue, but I would like to check the settings if possible.

thank you! MC NECK.MCX-7

The other issue is I don't have access to X7 so I am unsure what toolpaths you have available. But if you post a file/model others might be able to help you. This place usually pretty dead over the weekend, so probably won't see much until tomorrow.

Thank you. I'll try raster. I like Scallop because I can get the shaft and transitions continually and produce a smoother cut. But what do I know... I can share a file. MC file or model? Thanks again!

Hard to tell what your geometry is from the picture. Can you share a file? You might be trying to do too much with 1 toolpath and it may be easier to break it into sections I would try a Raster for the straight section of the neck. Then use a Blend/Pencil/Flowline for the transition area.

Hey guys, I've wasted so much time with this its making my head hurt! Please help! I'm running X7 and Constant Scallop toolpath. High Speed scallop is available but I can't figure it out. Trying to machine a guitar neck. Constant Scallop sounds like the best option given my limited knowledge. I've messed around with arc filters and redid the model several times but the toolpaths were still very jagged creating a lot of unnecessary code. Please see first pic. After several changes I came across the "sharp corner smoothing" which make the code a lot smoother BUT produced a weird Z plunge on one side of the model. Very strange. I thought it was a model issue so I mirrored the model to have 2 good halves. Same issue. Does anyone have any idea what may be causing this? Thank you!

Thank you. I noticed that the recommended settings for MCAM are 1920 x 1080 but when I change to this it makes everything a little blurry. I checked the slider as well to allow windows to make changes to this due to scaling errors.

That's usually for the ops manager setting. I would try your monitor resolution settings. Accessibility Management in windows may be able to scale it for you also

Good Morning Everyone, 1st time posting and hoping you all could give me some help. I just bought a new computer and after loading MasterCAM I noticed that some of the button icons are insanely small. Ive already tried the ENABLE LARGE ICONS option and it changes other buttons but has no effect on the ones in the image. Has anyone else experienced this? Any help would be greatly appreciated. This happens on all the pop up windows.

To yo mutha

What You can do is record the orientation parameter and insert g10 line to write it in the tool change macro and when you call up your tool you could write whatever difference you need to the orientation parameter.

As expected. Every machine tool builder does it differently, some don't do it at all, and others it's an option. No guarantees implied or expressed. What you do with your machine is between you and your employer. I'm not responsible for what you do with this information. https://www.dropbox.com/s/n2gdvagukqzoxd2/FANUC Spindle Orient by Angle Procedure.pdf?dl=0 https://www.dropbox.com/scl/fi/i2lwpzmuahj8hyddl9jer/O9028.TXT?rlkey=adfa5pujdj7h12oiulevh7gvs&dl=0 https://www.dropbox.com/scl/fi/ifwe8w08nnd24rpl5bf89/O9029.TXT?rlkey=l8ryh0ae1q66fb6pyp0nhxu56&dl=0

This sounds like the machine has glass scales to improve accuracy. One of the scales is broken or has become contaminated with coolant and swarf. The correct fix is to clean or replace the scale. The cheap fix is to disable the scales. This may affect the accuracy of the machine, but will get the machine running.

Greetings. Simple solution: Edit your set file to get output only for tool number and tool information. in ppost$ create logic which will call output from the set file and set it in your normal post output. To do that you need "target string" so post can know where to place the output if you like this idea PM so i can send you logic for the ppost$ postblock. Kinde regards. Ivan.

Good luck seeing how this is a 19 year old post.

I have a problem in my machine it's Toshiba BTD110 R 16 the alarm is ABS scale voltage low How to fix it

everybody do the dinosaur

Notice on my example I have a .0001 spacing on each chain. I turned down the chaining tolerance to .00005 to allow me to grab each chain. I only drew the top part of the motion approach then Dynamically transformed the bottom retract out chains

When i am in put M19 S .344 do not work

I misread this just now. Turn a boss on a flat bar? Shape a boss on a flat bar? Broach the shape around a boss on a flat bar? Forge a boss on a flat bar? EDM sinker to create a boss on a flat bar? Weld a boss on a flat bar?

Need to be careful adjusting that parameter if it has one not to throw off the tang to the tool arm. I would adjust me tool in the holder to get that difference out. See if what river hunter posted works then you have the easy button. Scratch the multi pass with Contour 3D. 3D with transform, but I would Draw my path to come out of the key way with each cut not dragging it back up. Where the Macro process is better because the down stroke can be the Repeated part that macro call X number of time. Here is a sample both ways. 5TH AXIS BROACHING EXAMPLE

thank you ,let me try