MIKE_B
-
Posts
406 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Store
eMastercam Wiki
Blogs
Gallery
Events
Everything posted by MIKE_B
-
But we still get no swag Terry.....
-
I did a remove of mcamx and then mcamx2 maintenance release 1 showed up on the list Just removed it and I'm gonna try to install again. Thanks for the help as always Mike
-
Yes I have admin rights I thought I checked the overwrite option but it did not install that way. Now I have 3 seperate mcam folders and its getting confusing where stuff is being pulled from. I have mcamx folder mcamx2-mr1 mcamx-backup All with the same subfolders
-
John I I tried that but the repair option does not come up. Here is my Add/remove list Add/Remove
-
web page I don't see it here?
-
Hi all I did't like the way my MR1 was installed so I went to uninstall it but I do not even see it listed in my "add/remove" program list. Any ideas? Thanks Mike
-
Solid Works .sldasm files X2 MR1
MIKE_B replied to Matt Berube at Ferron Mold's topic in Industrial Forum
Hi Matt I just tried a couple and had no issues they seemed to come in with no problems. -
Happy Happy! Thanks to all involved
-
Not the top two arrows you need to click the red arrow under those two.
-
Hi Rekesh In your ops manager right click on geometry >> change start point >> then click red arrow. Then you can move the start point anywhere along the chain
-
He can not save as a solid. He is running X2 without solids. I'm in the same boat myself
-
Paul Are you sure about the .003 chip? I would think more along the lines of .0003
-
Thanks John sent
-
Hey John if your out there what was this fix. I am playing around with the latest mpmaster and I'm getting T0 M6 at the end?
-
Thanks Paul Yes the corners do need to be sharp. I'll give the slower sfm a shot
-
Hi all I have a sheetmetal job here that I need to do some secondary work to. The Material is 301 FH. I'm using a 1/8 4 fl carb em going .025 deep. I just need to c'bore some holes but the corners of the EM are chipping. I am currently running at 300 sfm and .0003 chip. Is this to fast? Any Ideas? Thanks Mike
-
John I use comments for almost every toolpath I do just for this purpose. I just fished a part with 225 operations and it takes some time just to search through my comments. I'm thinking I might try typing them in English next time....
-
I'd like to be able to pick a pc of geometry and have to operation expand or highlight in some manner. This would be a great addition for long programs
-
Make sure to wear a mask. The dust can be nasty if you breath a lot in
-
When I analyze the same depth it shows a 3 place decimal.....
-
Lee Right now my system tolerance is unchecked. But it does have .00005 in it. Not sure this is what I need to change.
-
Ok guys I think this is an easy one but not sure how to fix it. If I select a pc of geometry... say for a "Z" depth. How do I get it to only show as a 4 place decimal in the parameters? Right now I'm getting 6 places? Thanks Mike
-
Hi Jack I just installed the 1500 and is working great. I am running the latest driver also 91.36. Good Luck And welcome to the forum Mike
-
Hi all Should hitting enter on the keyboard work when doing adjustment in the change at point field? I was spot drilling some holes then went into the change at point field to adjust some depths and I was hitting enter. I then posted the program and there were no Z differances. I went back and found I had to hit the green check and not enter. Is this the way it should be? From what I remember I was able to hit enter in this field in MR2.....but I have been known to be wrong.... Thanks Mike
-
Thanks James