Vericut interface for X6

[gcode]

I contacted CGTech today to ask about the Vericut interface for X6.

 

the reply was , sometime in the next few months.

 

 

 

[Greg Williams]

Ouch

[gcode]

Verisurf said the X6 version of their free Mastercam toolkit was several months out too. ( and I sure do miss it !!!!)

The reason given was all the new code in the x64 version...

Just a guess, but I'll bet Vericut is facing similar issues

[Zoober]

Between X+ and Vericut, that puts X6 on hold for us.....

Back to X5 till then

[Greg Williams]

^^^ Same here ^^^

[Aeroguy]

I contacted CGTech today to ask about the Vericut interface for X6.

 

the reply was , sometime in the next few months.

 

 

 

 

I almost fell over laughing when I read this. I guess CGTech isn't in much of a hurry to do anything where Mastercam is concerned.

Not that I blame them much either.

You would think that if they were serious about supporting MC users they would have a usable version for X6 out at virtually the same time, but then again, that would require communication between CNC and CGTech, and it doesn't look like that's happening.

 

Too funny.

[Jroc85]

I contacted CGTech today to ask about the Vericut interface for X6.

 

the reply was , sometime in the next few months.

 

 

 

 

In the next few months we'll be using X7.

[gcode]

In the next few months we'll be using X7.

 

 

I think not

[Jroc85]

I think not

There doesn't seem to be a sense of humor in here.

[gcode]

You 2 guys quit patting each other on the back and get back to work

[Aeroguy]

You 2 guys quit patting each other on the back and get back to work

 

[Jroc85]

You 2 guys quit patting each other on the back and get back to work

Gotta do something to pass the time.

[overthecrossbar]

NICE!!!!!! Meantime Muggins here's working his xxxx off my shoulders are sore from carrying you clowns.

[gcode]

NICE!!!!!! Meantime Muggins here's working his xxxx off my shoulders are sore from carrying you clowns.

 

builds character

[Jroc85]

NICE!!!!!! Meantime Muggins here's working his xxxx off my shoulders are sore from carrying you clowns.

You seem to have a lot of time on your hands with all the smiley faces.

[overthecrossbar]

one of these days buddy

[Jroc85]

one of these days buddy

Straight to the moon?

[overthecrossbar]

[Mgrenier]

Just heard from CGTech today and the say it's a top priority and should be out within 2 weeks.

 

 

[gcode]

thanks for the update

[Thee Rickster ™]

You seem to have a lot of time on your hands with all the smiley faces

 

If you three are in the same office, why do you argue on the forum?

jez reach over and smack each other....

[Jayson Kramer]

Any of you going to the User Group for CGTech on March 5th? I may be going.

[Jim Huddy]

The Mastercam X6 interface is a top priority. As is finishing up the Espirit interface, the Surfcam interface, and the Catia V6 interface. With any luck, they will all make it into the 7.2 release. And to find out when version 7.2 will be released, you will have to show up to the annual VERICUT User Exchange March 5, 2012 in Irvine, CA. That is when I, and more than 100 VERICUT users, will hear about the projected release schedule for 7.2.