Salahuddin
-
Posts
256 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Store
eMastercam Wiki
Blogs
Gallery
Events
Everything posted by Salahuddin
-
Wlcome to the forum and yes we can
-
this issue can be seen with the sample file that came with MCX the file is: contour finish high speed corner rounding-mm.mcx you can see that the surface finish result will be better if you don't use the filter
-
when I use filter in surface contour toolpath I got a bad surface finish, especially on round parts and on the corners of other shape parts this start to happened in ver. X, I used it all the time in ver 9 without any problem. Without filtering I got nice surface but with longer program MR2 installed I am using filter ratio 2:1 Total tolerance 0.02 mm One way filtering. I tried to change a lot to work around this issue. In verify , simulate tool, it can show me that the surfaces not perfect. I didn’t read any one wrote about this issue, so maybe its only with me!!!!!
-
the chain you use, is it lines and arcs or spline? if spline, change the start point of the chaine hope this will help
-
its not understood to me Matt, in the HST area toolpathes, it will leave or goug withinn the tolerance???!!!! I know that if I want the tool to go to -9 mm I don't want it to go to 8.995 mm, so accurate work we have to do with normal surface pocket??
-
In the HST-area clearance metric sample file, the tool should go to Z -9 mm, instead it go to -8.995 mm leaving 5 micron!!! If I create surface pocket toolpath on the same part it go to -9 mm as it should This situation happened also to my parts, so it’s not just with this sample part. I don’t have the Inch Samples, so I can’t check if this happened to there also??? MR2 installed here Any Ideas????
-
its new to MR2, you can saw it in the MR2 video. its very nice.
-
it will be 3.9 IPM
-
I tried it on computer only, but not on real work at machines. I think I will wait to see it in mr2
-
it didn't crash for me for some time now. I think hardware play a big resone for crashes so maybe you can try the same part on two diff computers, one will crash and one wont. for that reson reporting the crashes to qc will help them in solving such problem. and I don't think reporting the crash here will help
-
so it will be something rotate and translate in one shot, its nice if Mastercam will have this option in future.
-
at properties, what the capacity of the file now? do you use the Autosave? this isse was coverd several time, and I think that you need to start over
-
if you make a search, you will find a lot of topics about this thing, any way you have to set mcam to use about the half of your ram which is 1gb in your case
-
I have the same crad , but witout this issue that you have
-
what is your display card?
-
which mode is selected? the trace or run mode? you have to select the run mode
-
under the quick verify icon there is icon called restrict drawing, this icon will clean the toolpathes
-
Drill Toolpath and Transform
Salahuddin replied to Namliek_J@TheeCircle™'s topic in Industrial Forum
are you using the transform rotate? what is the number of step you use? I used rotate without any problem in X -
Go to control def > click on tool > tool offset registers > add to tool > length 0 diameter 0 and it was coverd several times
-
I wish you all the best, and thanks for all the help.
-
MR1 High Speed Scallop always starts inside
Salahuddin replied to Ed@Elite's topic in Industrial Forum
I just tried it and its work fine with the reverse direction. I used the HST scallop file that came with sample I have the X MR1 -
Hi Hans, this issue was coverd several times, if you make a search you can find about it here is a link: http://www.emastercam.com/ubb/ultimatebb.p...t=019046#000000 and welcome to the forum
-
yes thats help in the all edges only, its not a bad way till the next release thanks
-
so, did any one tryed to creat and edge curve on a 2D suface without getting splines?
-
Its 2D, to try it I create a rectangular and create flat surface from it, delete the rectangle chain, and create curve on that surface, before MR1 I got line on that surface, now , I got only spline, I tried another thing, if I create solid from the surface and create curve on the solid I got lines and arcs as it should. Something wrong here!!!!