Leon82
-
Posts
2,193 -
Joined
-
Last visited
-
Days Won
12
Content Type
Profiles
Forums
Downloads
Store
eMastercam Wiki
Blogs
Gallery
Events
Everything posted by Leon82
-
New machine incoming,.. now looking at toolholding
Leon82 replied to Kyle F's topic in Machining, Tools, Cutting & Probing
Yes it's just the fingers on matsuura -
New machine incoming,.. now looking at toolholding
Leon82 replied to Kyle F's topic in Machining, Tools, Cutting & Probing
Haimer makes holders as well as lyndex. We use haimer shrink and their er collet holders. We have a few lyndex slim chuck and dream holders also. Command also but they don't make their 3" er11 holders in bt40 anymore -
On the website it's not listed. We may be acquiring a used 500u with the HEIDENHAIN control .
-
I usually only combine two ops in one group if I have to share a lot of tools and am flipping between one side then the other with each part.
-
Does anyone use sandvik 460 drills?
Leon82 replied to Leon82's topic in Machining, Tools, Cutting & Probing
I ordered a ypl drill I'll see how it works -
Do you have the filter turned on to make arcs in x and y? It's possible that controlled definition is forcing linear moves
-
Usually you would have a g49 above it, then activate the tool offset. It's been a while but on the old shops 2xi we used g5.1q1 but I believe the option was g5.1 P10000 Is it fanuc or their new os
-
Does anyone use sandvik 460 drills?
Leon82 replied to Leon82's topic in Machining, Tools, Cutting & Probing
Thanks. I went back to the guring firex for now. I'll look at those -
Does anyone use sandvik 460 drills?
Leon82 replied to Leon82's topic in Machining, Tools, Cutting & Probing
About .005" I put a small spot in and it helped. I changed the drill and lowered the sfm. I'll see if it holds up -
I have an Amazon ender 3 clone
-
We are cutting grade 5 titanium and the website says 4000 rpm at 19 ipm for a .177drill. I tried it at 85% of that and it didn't like it. It walked pretty bad. 1 inch deep .177dia 1200psi tsc in a hammer shrink. No peck and no spot drill. It was at 13%load on the mam 72-35v. Anyone use these in titanium before?
-
It moves a lot. Let it sit in QC for a while to acclimate
-
This is where the circles with lines comes in handy I believe. Use hole axis and get yourself a line
-
I think if you you under updates you can pick just the Camplete
-
I haven't figured out if you can omit it from a new install
-
we have two but one is manual guide i and the other is the new ihmi. but they do the same thing
-
plus re machining doesn't respect internal radius
-
Best Extended Reach Tools for Milling?
Leon82 replied to [email protected]'s topic in Industrial Forum
i usually use a stub flute and have to step it down -
It has spikes in the red when it starts to grumble. Raising the rpm usually helps
-
in the subsequent cycles section under the drill cycles in the post
-
I used to work with cranky Hank and he would have .499 .374 ect end mills in his programs. you should see how he adjusted his threadmills
-
it rounds the top even with a flat endmill. if the corner were shart technically it would have more material on it than what you set. there is a setting for stock to leave not to round corners in contour. maybe something similar. or a check box in tool path fillet to make sharp
-
in the graphics world up and down is Y and z is depth in the monitor view
-
Both clamped
-
I'm taking relatively light cuts with a 3 flute endmill in aluminum. It starts to rumble and you can see the z load increase. Sometimes it pulls the head down into z excess error servo alarm. Its at 70% load just sitting still with no cutting. It looks like the motor is the same size as the 520
