What are you tapping? Probably hergoslovania

I've seen some funky looking swarfs that were remedied with additional sync lines.

Drip feed? Is there an option to execute a file from memory card?

Does that mean no more alt Z? And ALT F1 I remember when there were no icons

A while back I was playing with the stand alone tool manager and I think from there you can import a dxf file for your tool. There were 2 colors for cutting and non cutting geometry. I never mess with it but maybe it can help you out

You made a c axis pun lol

My coworker experienced this on one of our MX 520 trunnion machines. The rotary spun 270 degrees while the cutter was down in the pocket. Very hard to see in camplete unless you slow it way down. He almost had to change his shorts

These can be added by canned text and applied thru the canned text page on the tool path. You should be able to add it in the canned text control definition page.

If I'm understanding him right, he doesn't want anything to change when he clicks on a different size tool, so he will need to deactivate recalculate hsm defaults. It is in the system settings possibly under toolpaths.

If the goal is to keep the tool down, once your depths are good you can set the retract to incremental zero and set clearance to start and end of operation only. Obviously it can go bad if your not careful, but I have done this to cut to rails on a part with out raising the tool

Feedrates or tool path parameters? I always put my speed and feed in the tool page not the dialog path in the tool path parameters page. In the configuration setting there is an option for recalculate hsm defaults. I think this is what you are looking for. I don't remember the exact page but its there somewhere.

They work great when using a longer endmill . you don't need to worry about it loading up in the corners. My only gripe with the 2d high speed is if you are roughing and OD of a part with bosses on it , it tends to radius off the part and come back close to keep the travel distance down. With a back feedrate of 500 or 750 the machine is slowing down to maintain the precision. On the matsuura I usually go to r5 precision because lower and you start to hear the direction changes in the ball screw. Our machine with linear motors is smooth a pie though.

We use CID jhh series a lot

We have a ps95 with a professional p control. I would not recommend that control.

2018 is almost here? I guess my company's going to skip 2017 lol. Or always be a year behind

Thanks, I had 2 paths for facing it parallel so it wasn't too bad. Luckily the part had no holes outside of the travel envelope. It probably only will come up once and a while but its nice to know we could do it if needed. I'll have to try that in camplete when I have some free time.

I usually turn the Maxima ark up to 5,000 and hit the save button . Bump up the tolerance, but not more than the stock you're leaving

Haimer lists their 1/8 shrink at .390 od

I agree,but convincing the boss is another story. We minimize thru spindle coolant and I added an m16 in camplete to override the chassis rinse.

Had this issue with a .02 mm true pos. All sides machined. All holes were being bored Matsurra guy came down said machine is fine. Thermal growth is the problem. Thru spindle collant will heat the enclosure 10 degrees or more. Run the coolant low, fill it up with cold water and watch it shift on you, lol Ended up putting an moo and indicating the part for each piece using the g54.4 active workpiece function. They usually come in at 10 to 15 micron true pos

Ref point #1 is 1240 Then you have 2&3 next

I believe its 1815. For motor origin Once you switch it to 1 it prompts you to shut it off. Just confirm in the book. If you want 2nd or third reference point it may be near 1320(soft limit parameters) Limit

I had a fixture to make that was too big for our mx520 trunion machine. The machine has more travel in x- direction I selected 3axis in the rotary tab, but we use camplete posting software and it is not being imported correctly. To be clear the machine moves to y0 then stays there while xzc do the moving So I took a 4 axis generic post and made the rotary rotate about z and got a path to post on the x+ side. I played with the home position and start angle in the machine def but it made no difference. So I was able to butcher thru it by programing it 180 deg transform in z and using the tilting work plane at the machine to rotate it back. Posting a 180 degree z rotation did not work though. I had to take the first rotary move and add 180deg to it to get the machine to stay at y0 position. This worked, but means each tool needs its TWP rotation value entered by hand. I browsed thru the post and machine def and can't find a way to force it to stay x- Thanks Leon