Leon82
-
Posts
2,195 -
Joined
-
Last visited
-
Days Won
12
Content Type
Profiles
Forums
Downloads
Store
eMastercam Wiki
Blogs
Gallery
Events
Everything posted by Leon82
-
MCAM 2024 - takes 5-7 seconds to load tool library
Leon82 replied to Tinger's topic in Industrial Forum
I had 3 sessions open for a couple days. -
MCAM 2024 - takes 5-7 seconds to load tool library
Leon82 replied to Tinger's topic in Industrial Forum
have you restarted? sometime when i analyse an entity it takes about 5 seconds for the box to show up. restarting fixes it -
Is the linearize helix button checked? I can't see the file at home.
-
Check the minimum radius and XY clearance in the entry motion section. I usually set mine to 1% and 45%. XY to .005 or less depending on what I'm doing. Also check your clearance planes and feed planes
-
Yes.you just have to linearize the path. The matsuuras have That but it remains at the reduced speed until the tool stops I believe. It has a lamp called spindle overload.
-
kinematic adjust question fanuc
Leon82 replied to Leon82's topic in Machining, Tools, Cutting & Probing
I re ran ez5 and left the x number alone and it seems to be ok now. It must be a combination of the y x half and 70mm below centerline -
i have x and y dialed in to bout .0001 on all 4 sides all five sides are faced and the tool offset is dialed in within .0001 i cant get this number to move, what parameter is it? the holes are .0007 too close to the top face moving z , the 70mm offset and half offset does nothing except make the tool offset different.
-
not since going to 2023. its is a pain because i have to get the system admin password every time , multiple times and only two people have it
-
Probing with Twp would probably work if you have it. Otherwise you could do some math with variables and the center of rotation. We use mastercam drill cycles for probing
-
Yes years ago I ended up with a custom bolt circle
-
If you move you mouse and accidentally hit the wheel as you pass over it could change them inadvertently
-
you can wire edm a slot gauge so it can't be forced in like a pin or trim a gauge block to fit
-
corollate it with the cmm or deltronic pins. if its aluminum switch to a silicon nitrate probe. it will build up on the ruby
-
the top one had keep tool down for finishing the bottom is keep tool up i came back after lunch and the machine said modal out of g40 Ill see if i can strip the file , on 2023 update 3
-
Use inverse for rotary.
-
Solid Carbiude Slitting saw
Leon82 replied to AMCNitro's topic in Machining, Tools, Cutting & Probing
What diameter? Internal tool has some big thin ones braised to a hss shank -
Do they still have the x20 increment for the handle feed? That was pretty cool moving 2 inches per rev
-
Probably ok with a dynamic path.
-
It was installed with the Camplete installer when we updated
-
you can use quotations to post directly what's in them in the tool change block before pcan result = newfs(15, feed) #Reset the output format for 'feed' pbld, n$, *t$, sm06, e$ pindex after pbld, n$, "G28", "X0", "Y0", e$ pbld, n$, "G30", "X0", "Y0", e$ pbld, n$, sm01, e$ result = newfs(15, feed) #Reset the output format for 'feed' pbld, n$, *t$, e$ pbld, n$, sm06, e$ pbld, n$,sm01, e$ pbld, n$, "G28", "X0", "Y0" e$ pbld, n$,sm01,e$ pindex
- 5 replies
-
- 2
-
-
-
- tool number
- t1
- (and 7 more)
-
Move program name below program number in post
Leon82 replied to Odin's topic in Post Processor Development Forum
I think That will cause the program name not to appear in the machine directory . -
Move program name below program number in post
Leon82 replied to Odin's topic in Post Processor Development Forum
looks like line 2173 put an e$, after progno$ and create a new line with the proper spacing for the name -
Down and dirty contour with tapered walls
-
APparently the customers require lots of cyber security stuff.
-
we network save also.
