Leon82
-
Posts
2,195 -
Joined
-
Last visited
-
Days Won
12
Content Type
Profiles
Forums
Downloads
Store
eMastercam Wiki
Blogs
Gallery
Events
Everything posted by Leon82
-
What's the best way to become an expert on the 3D Toolpath section?
Leon82 replied to volitan71's topic in Industrial Forum
I was making parts for a company and the guy called and said where are they. I said we're working on them and he said"what does that mean, you haven't started them yet?" So I said yes. -
In the settings chech the startup settings. It's in there somewhere
-
In the controller definition disable staged tool routines
-
It may want an R instead of a I and J depending on the controller.
-
What do the linking parameters say? Double check the top of stock and feed plane
-
Insert Third Party Ribbon Tabs
Leon82 replied to Mavyhui's topic in Post Processor Development Forum
I know Camplete had an addmenu.dll.- 1 reply
-
- 1
-
-
What's the best way to become an expert on the 3D Toolpath section?
Leon82 replied to volitan71's topic in Industrial Forum
Power surface can be handy with split holes. I have no idea how to use it but for roughing it is good -
What's the best way to become an expert on the 3D Toolpath section?
Leon82 replied to volitan71's topic in Industrial Forum
In that case I make a surface and un trim. Or surface fill holes is an option if it's a full hole -
Im doing a part in a 520 pc4 that is a swarf cut in A axis which does a 180 degree unwind at A0. it leaves a tiny raised edge at this point. it can easily be smoothed but am wondering if it can be made better. im using g131 f3 and the slider is on max precision. the other alternative is to break it up but i would have to conventional cut one direction .
-
Is it supposed to have a g91 in that line? That seems dangerous. Had cutter comp been deactivated from the previous path?
-
H#518 on the matsuura. We have Camplete set to output the variable instead of tool number. That gets updated with the tool life
-
I believe the output for data is there too
-
You can do it in the tool manager from the main control. On our 850 with 60 tools I added 30 for a job. I go in unload the data for the tool I'm taking out and load in the data for the tool I'm putting in. Then put a tool tag on it. You can only load it into a free pot. I call up tool zero because if you unload the tool while it's in the spindle it won't recognize it untill after a tool change
-
If your plan is to share them I would do a mastercam Library
-
Transitioning from Control to Wear
Leon82 replied to zmassingill's topic in Machining, Tools, Cutting & Probing
Can you use a system variable to warn in the program? Like if dia comp is greater than .005 issue alarm or program stop? -
G184 on the 840di Siemens
-
Trim toolpath not working in 4x cor setup w/ contour multi-pass
Leon82 replied to SlaveCam's topic in Industrial Forum
Dynamic kind of is its replacement in a way -
Ok. I'll have to look.
-
A couple guys when they verify with a manual entry it opens and immediately closes Has anyone experienced this in 2023?
-
What does the ptool_inpection look like? Personally i would copy some of the ptoolcng block so it re issued everything. This way if for some reason somebody goes to start the program from there it's going to have the right tool and the spindle.
-
Call out X,Y plane after toolchange
Leon82 replied to Rstewart's topic in Post Processor Development Forum
Did you do it in the tool change block? Don't do it in the null or pretract or prapidout -
There should be a post block labeled subsequent holes underneath the drill cycles
-
It sounds like the spring pass is removing lots of spring
-
Call out X,Y plane after toolchange
Leon82 replied to Rstewart's topic in Post Processor Development Forum
You could try an asterisk In front of the sgplane *sgplane -
You really don't have a choice but to make a center cut. You can order a smaller one and do some multipasses and finish with the full size cutter
