53,338 topics in this forum

1. X+ tool list

   By YoDoug®, March 23, 2010
   • 2 replies
   • 259 views
   • 
   • YoDoug®
   • March 23, 2010

2. Solid chamfer on scalloped edge

   By landscnc, February 22, 2010
   • 4 replies
   • 259 views
   • 
   • landscnc
   • February 22, 2010

3. New auto hightlight by solid face feature

   By Guest, October 25, 2006
   • 0 replies
   • 259 views
   • 
   • Guest
   • October 25, 2006

4. Spline conversion v9.1

   By jmarc, June 25, 2003
   • 0 replies
   • 259 views
   • 
   • jmarc
   • June 25, 2003

5. SPEEDS & FEEDS

   By reaper01, February 20, 2007
   • 2 replies
   • 259 views
   • 
   • tonyc
   • February 21, 2007

6. Solid/mesh stock wont stick in 2021 - fixed in 2023?

   By SlaveCam, October 5, 2022
   • 1 reply
   • 259 views
   • 
   • CEMENTHEAD
   • October 7, 2022

7. Unable to see custom tool when i verify

   By rdogg, January 17, 2007
   • 2 replies
   • 259 views
   • 
   • rdogg
   • January 17, 2007

8. Tool Bar has gone

   By GREG, April 9, 2003
   • 3 replies
   • 259 views
   • 
   • GREG
   • April 9, 2003

9. New Computers

   By ChrisD, February 20, 2003
   • 1 reply
   • 259 views
   • 
   • Mark H
   • February 20, 2003

10. O/T kennametal KSEM drill inserts

    By Philcott, June 2, 2003
    • 2 replies
    • 259 views
    • 
    • Philcott
    • June 2, 2003

11. job setup__ adjust feed on arc move

    By mayday, June 26, 2003
    • 2 replies
    • 259 views
    • 
    • Tony
    • June 26, 2003

12. wire problems

    By PERRY C, September 17, 2007
    • 9 replies
    • 259 views
    • 
    • PERRY C
    • September 18, 2007

13. Active viewsheet finally saving...

    By SlaveCam, August 20, 2018
    • 0 replies
    • 259 views
    • 
    • SlaveCam
    • August 20, 2018

14. R 5400 RACK WORKSTATION

    By Hacsta, October 3, 2008
    • 1 reply
    • 259 views
    • 
    • Hacsta
    • October 6, 2008

15. material removel by plunging

    By rex miller, March 6, 2005
    • 3 replies
    • 259 views
    • 
    • ARP
    • March 6, 2005

16. Edit post re: decimal points

    By gti_jay, December 6, 2005
    • 2 replies
    • 259 views
    • 
    • gti_jay
    • December 6, 2005

17. Post help! X and Y switch places

    By Sandybar, February 15, 2005
    • 9 replies
    • 259 views
    • 
    • Sandybar
    • February 15, 2005

18. Ver 9 to Ver X lathe post

    By Columbo™, February 26, 2007
    • 1 reply
    • 259 views
    • 
    • Guest
    • February 26, 2007

19. pocketing

    By dprovost71, April 23, 2007
    • 3 replies
    • 259 views
    • 
    • doyleg
    • April 23, 2007

20. Unified Start Point Control

    By Jake L, May 19, 2023
    • 3 replies
    • 259 views
    • 
    • Jake L
    • May 19, 2023

21. surface toolpaths

    By Santa Fe, May 11, 2007
    • 5 replies
    • 259 views
    • 
    • 3R!< W3NG3R
    • May 12, 2007

22. Solidworks 09 translator??

    By rsbeadle, November 25, 2008
    • 1 reply
    • 259 views
    • 
    • Pete Rimkus from CNC Software Inc.
    • November 25, 2008

23. lathe and mill

    By cappy, March 6, 2008
    • 3 replies
    • 259 views
    • 
    • crazy^millman
    • March 6, 2008

24. G07

    By mastercarp, June 11, 2008
    • 5 replies
    • 259 views
    • 
    • YoDoug®
    • June 11, 2008

25. Tooling suggestion request

    By mcpgmr, October 14, 2009
    • 4 replies
    • 259 views
    • 
    • MotorCityMinion
    • October 21, 2009