2,522 topics in this forum

1. Turret selection handled in post?

   By gms1, May 17, 2011
   • 2 replies
   • 2k views
   • 
   • gms1
   • June 29, 2011

2. Post processor developers

   By Tiago Pereira, October 30, 2019
   • 2 replies
   • 732 views
   • 
   • ihsDavidGB
   • October 30, 2019

3. Makino a51 Health Data extraction

   By Andrewaz, September 23, 2019   

   • makino a51
   • data extraction
   • 2 replies
   • 408 views
   • 
   • Andrewaz
   • September 26, 2019

4. G02 and G03 Modal

   By ajkdemusz, November 18, 2011
   • 2 replies
   • 1.5k views
   • 
   • Bryan Johnson
   • November 21, 2011

5. Mpmaster post not outputting correct address for rotary axis

   By Mgrenier, January 25, 2013   

   • in psof post block
   • 2 replies
   • 1.3k views
   • 
   • Chris McIntosh
   • February 8, 2013

6. Mastercam's Mazdak Integrex 100-IV ST machine definition

   By mjabbour, November 13, 2015
   • 2 replies
   • 1.2k views
   • 
   • Guest
   • November 13, 2015

7. Lathe sub spindle work offset

   By nayebi, July 6, 2019
   • 2 replies
   • 742 views
   • 
   • nayebi
   • July 18, 2019

8. Xform rotate count instances

   By bd41612, May 20, 2022
   • 2 replies
   • 684 views
   • 
   • bd41612
   • May 23, 2022

9. HAAS "BEEP" SOUND

   By PcRobotic, December 12, 2019
   • 2 replies
   • 812 views
   • 
   • Colin Gilchrist
   • December 12, 2019

10. HWACHEON HI-TECH350 Lathe post

    By MSL, November 14, 2016
    • 2 replies
    • 1.5k views
    • 
    • MSL
    • November 14, 2016

11. Mastercam post-processor migration/update

    By Abdul Hakim, July 8, 2019
    • 2 replies
    • 853 views
    • 
    • Abdul Hakim
    • July 9, 2019

12. Stock advance Misc operation

    By BBprecise, October 7, 2014
    • 2 replies
    • 1.2k views
    • 
    • BBprecise
    • October 8, 2014

13. tt_count$ mystery - logic for tools called up more than once

    By JCDFCM, June 9, 2021
    • 2 replies
    • 425 views
    • 
    • JCDFCM
    • June 9, 2021

14. xtooltable

    By BenzB, June 13, 2017   

    • tool table
    • xtooltable
    • 2 replies
    • 841 views
    • 
    • So not a Guru
    • June 25, 2017

15. WIRE THREAD POINT

    By eltklas, April 17, 2023
    • 2 replies
    • 663 views
    • 
    • eltklas
    • April 28, 2023

16. Post For Prototrak SMX

    By drenfrow, June 5, 2014
    • 2 replies
    • 4.6k views
    • 
    • Guess_who
    • June 10, 2014

17. Index G220 Turn Mill Post

    By synkboy11, November 6, 2018
    • 2 replies
    • 953 views
    • 
    • Robert Bernobic from CNC Software
    • January 28, 2019

18. how to add multiple spindle M code on & off of 3 axis machine

    By Vilas Reddy, May 23, 2017
    • 2 replies
    • 873 views
    • 
    • Craig-B
    • May 26, 2017

19. I & J post out

    By Metric, May 17, 2012
    • 2 replies
    • 990 views
    • 
    • Metric
    • May 17, 2012

20. output M-code with angle for indexer

    By Doug Funny, December 23, 2022
    • 2 replies
    • 494 views
    • 
    • Leon82
    • December 26, 2022

21. Oops!

    By tsaladyga, January 16, 2012
    • 2 replies
    • 1.2k views
    • 
    • K2csq7
    • January 16, 2012

22. Last but not least, cc_pos$

    By ahaslam, October 13, 2015
    • 2 replies
    • 913 views
    • 
    • ahaslam
    • October 14, 2015

23. Active Reports - Setup Sheet

    By xxedraxx, January 26, 2020   

    • setup sheet
    • 2 replies
    • 638 views
    • 
    • Jandr0
    • January 27, 2020

24. osp workoffset again

    By Metric, May 17, 2012
    • 2 replies
    • 6.2k views
    • 
    • Guest
    • May 21, 2012

25. the post is not run notepad?

    By Lee1, July 27, 2012
    • 2 replies
    • 1k views
    • 
    • sobrien51
    • August 15, 2012